SAF-HOLLAND FleetMaster Air FW8 Series Скачать руководство пользователя страница 12

Страница: 12 / 20

XL-FW501 Rev C

OPERATING INSTRUCTIONS

continued

Position tractor and trailer on firm,

level ground clear of obstacles and

persons.

Set trailer brakes.

Slowly back tractor tightly against

trailer.

Set tractor brakes.

Chock trailer wheels.

Lower landing gear until pads just

touch the ground.

NOTE:

Follow instructions published

separately for safe operation of the

trailer to transfer trailer weight off

fifth wheel. Do not raise trailer off

the fifth wheel.

Disconnect brake lines and light

cord. Attach brake line to dummy

coupling to keep line clean.

If equipped, pull secondary lock

handle and hook on casting (located

on left/road side of fifth wheel).

Pull primary release handle.

10. Release tractor brakes and slowly

drive away from trailer. Let the

trailer slide down the fifth wheel

and pick-up ramps, being careful

that the trailer landing gear touch

the ground with minimal impact.

NOTE: It is normal after uncoupling for
the release handle to come off the
unlock notch and move to a “ready to
couple” position.

Uncoupling Procedures

UNLOCK
NOTCH

LOCK NOTCH

1st

2nd

3rd

“READY TO

COUPLE”

POSITION.

WHEEL IS OPEN.

PRIMARY

PRIMARY
RELEASE HANDLE

RELEASE HANDLE

SECONDARY

SECONDARY
RELEASE HANDLE

RELEASE HANDLE

OUT

LOWER
LANDING
GEAR

Содержание FleetMaster Air FW8 Series





















Результаты поиска

Содержание FleetMaster Air FW8 Series

Отзывы:

Похожие инструкции для FleetMaster Air FW8 Series

Бренды по названию

Популярные бренды

SAF-HOLLAND FleetMaster Air FW8 Series, Руководство пользователя

Результаты поиска

Содержание FleetMaster Air FW8 Series

Отзывы:

Похожие инструкции для FleetMaster Air FW8 Series

Бренды по названию

Популярные бренды