SAF-HOLLAND FleetMaster Air FW8 Series Скачать руководство пользователя страница 10

Страница: 10 / 20

XL-FW501 Rev C

OPERATING INSTRUCTIONS

continued

Chock trailer wheels.

Connect brake lines and light cord.

Support slack in lines to prevent

interference.

10. Set trailer brakes.

11. Adjust trailer height so fifth wheel

will lift trailer. Trailer should contact

fifth wheel 4˝ - 6˝ behing fifth wheel

bracket pin.

Attempting to couple
with the trailer at an

improper height may result in a false
or improper coupling, allowing tractor
and trailer separation which, if not
avoided, could result in death or
serious injury.

12. Slowly back into trailer.

13. Do a pull test as an

INITIAL CHECK

14. Visual inspection.

Get out of the tractor.

Visually check that the

lock is CLOSED!

An improperly coupled
tractor and trailer may

separate while in use which, if not
avoided, could result in death or
serious injury.

Do not use any fifth
wheel that fails to

operate properly. Failure to properly
couple tractor and trailer may cause
separation which, if not avoided, could
result in death or serious injury.

➠

PULL FORWARD WITH TRACTOR

PULL TEST

FIFTH WHEEL

WILL NOT LIFT

TRAILER

Wrong

FIFTH WHEEL

MUST LIFT

TRAILER

➠

FIFTH WHEEL

TILTED DOWN

4˝- 6˝

USE LOW

GEAR

TRAILER

BRAKES

LOCKED

LOCK

NOTCH
BEHIND

RIB

CHECK

RELEASE

HANDLE

CLOSED POSITION

NO GAP!

PLUNGER

LOCK JAW

AROUND

KINGPIN

PLUNGER

VISIBLE AS

SHOWN

TRAILER

BOLSTER

PLATE

KINGPIN

Coupling Procedures

continued

Содержание FleetMaster Air FW8 Series





















Результаты поиска

Содержание FleetMaster Air FW8 Series

Отзывы:

Похожие инструкции для FleetMaster Air FW8 Series

Бренды по названию

Популярные бренды

SAF-HOLLAND FleetMaster Air FW8 Series, Руководство пользователя

Результаты поиска

Содержание FleetMaster Air FW8 Series

Отзывы:

Похожие инструкции для FleetMaster Air FW8 Series

Бренды по названию

Популярные бренды