Saf-Fro DIGISTEEL III 320C, Инструкция по эксплуатации и обслуживанию, Страница: 10 / 28

10 / 28
List of accessible parameters in
Left
display
Right display Step Default
GrE
On
-
;OFF
–
Aut
ScU Nnc – no - OFF
CPt
OFF
–
0
,
01
–
1
,
00 0
,
01
s
PGM
Nno
–
yES
PGA
OFF
–
;000
–
020
%
1
%
rC Nno – yES
CAL OFF – on
L 0 – 50 1 uH
r 0 – 50 1
Ω
SoF
Nno
–
yES
FAC
Nno
–
yES
List of accessible parameters in
Left
display
Right display Step Default
tPt
00.5
–
10.0 0
,
1
s
PrG
00.0
–
10.0 0
,
1
s
tHS OFF – 00.1 – 10.0 0 , 1 s
IHS --
70
–
70 1
%
UHS -- 70 – 70 1 %
dSt
OFF
–
00.1
–
05.0 0
,
1
s
DdSI --
70
–
00.0 1
%
dSU --
70
–
70 1
%
Pr_
0.00
–
0.20 0
,
01
s
PrS
Nno
–
yES
PoG 00.0 – 10.0 0 , 05 s
dYn
-- 10 – 10
--
20
–
20
1 %
rFP
-- 10
–
10
--
20
–
20
1
%
dyA
00
–
100
1
tSE OFF – 0.01 – 2.50 0 , 01 s
ISE --
-50
–
50 1
%
3.3.4. Program management
DIGISTEEL III 320C / DIGIPULS III 320C allows creating, store and modifying up to 99 welding programs directly on front panel from
program 00 to program 99 . This function is activated by moving parameter
P00 is the working program in any state. (Program management mode activated or desactivated). When power source is working on
this program, the Led indicator “JOB” is switched off. All commutators are accessible in this mode, so it will be used to set
P01
to
P99
are program saved, only if program management mode is activated. When power source is working on these programs,
the led indicator “JOB” is switched on. In this mode, commutators welding process, wire diameter, gas and metal are not
When a program selected has been modified, the indicator “JOB” blinks.
DIGISTEEL III 320C
List of accessible parameters in
COnFIG
menu
Default Description
Aut
Configuration of the Water Cooling Unit. 3 possibles states :
- On : Forced on, watercooler is always activated
-
OFF
: Forced off, watercooler is always desactivated
- Aut : Automatic mode, Watercooler works when according need
OFF
Security of water cooling. 3 possible states :
-
nc
: Normally closed,
- no : Normally open,
-
OFF
: Desactivate
0
,
30
Trigger holding time in order to call program (Only in 4T welding mode).
Can be use only for welding program from 50 to 99.
no Activate / desactivate program management mode
OFF
Use to setup available adjustement range of the following
voltage, arc dynamics, pulse fine-setting. Use only when program management is
activated and programs are locked.
no
This parameter activates / desactivates remote control or potentiometer torch when plug
on power source.
OFF Calibration of torch & ground harness
14 Cable choke setting / display
8 Cable resistor setting / display
no Software update mode.
no
Factory settings reset. Pressing YeS will cause a reset of the parameters to factory
defaults when exit SETUP menu.
List of accessible parameters in CYCLE menu
Default Description
0
,
5
Spot time. In Spot mode and in Manual mode, the Hot Start, Downslope and sequencer
settings cannot be changed
0
,
5
Pre-gas time
0 , 1 Hot start time
30
Hot start current (wire speed). X%
±
the welding current
0 Hot start voltage X%
±
the arc voltage
OFF Down-slope time
--
30
Down-slope current (wire speed). X%
±
the welding current
0
Down-slope voltage. X%
±
the arc voltage
0
,
05
Anti-stick time
no Pr-Spray activation
0 , 05 Post-gas time
0 Fine setting in short arc
0 Fine setting in pulse
50 Arc striking dynamics at electrode
OFF Sequencer time (Sequencer, only in synergic mode)
30
Sequencer current level. X%
±
the welding current
creating, store and modifying up to 99 welding programs directly on front panel from
. This function is activated by moving parameter PGM from no to YES in COnFIG menu.
is the working program in any state. (Program management mode activated or desactivated). When power source is working on
this program, the Led indicator “JOB” is switched off. All commutators are accessible in this mode, so it will be used to set pro
are program saved, only if program management mode is activated. When power source is working on these programs,
the led indicator “JOB” is switched on. In this mode, commutators welding process, wire diameter, gas and metal are not available.
program selected has been modified, the indicator “JOB” blinks.
EN
320C / DIGIPULS III 320C
Configuration of the Water Cooling Unit. 3 possibles states :
: Forced on, watercooler is always activated
: Forced off, watercooler is always desactivated
: Automatic mode, Watercooler works when according need
to call program (Only in 4T welding mode).
Use to setup available adjustement range of the following parameters: wire speed, arc
setting. Use only when program management is
This parameter activates / desactivates remote control or potentiometer torch when plug
will cause a reset of the parameters to factory
In Spot mode and in Manual mode, the Hot Start, Downslope and sequencer
the welding current
the welding current
creating, store and modifying up to 99 welding programs directly on front panel from
is the working program in any state. (Program management mode activated or desactivated). When power source is working on
programs.
are program saved, only if program management mode is activated. When power source is working on these programs,
available.