background image

11

SETTING UP YOUR MACHINE / PRE-HEATING

SETTING UP YOUR MACHINE

1) Refer to Important Safeguards to make

sure the machine is located in a safe

place.

2) Your machine has been factory designed

to operate at a specific voltage. Refer to

the identification label on the bottom of

your machine to make sure that the outlet

you intend to use supplies the proper

voltage and that the circuit it belongs to

is rated for the machine's power

requirements. If an extension cord is

needed make sure that it also has the

appropriate rating and meets or exceeds

all safety standards.

3) Filling the water tank
•

 Remove the water tank from the

machine.

•

 Rinse the tank thoroughly and fill it

with fresh, cold water. We recommend

using only filtered or bottled water. Never

use anything other than cold water in

your machine.

•

 Reinsert the tank into the machine.

The water supply hose will automatically

be lowered into the water tank.

4) Plugging in your machine

Make sure  the power switch is in the

up and off position. Also make sure

the other switches are in the up and off

position.

• Make sure the outlet you are using is

appropriate for the machine and then

plug the machine in.

• Turn the power switch on. The switch will

illuminate to indicate that the machine

is on.

• Be sure to prime the machine right away

using the following instructions.

5) Priming the machine

• The machine must always be primed

before use and after steaming.  It is also

a good idea to prime the machine after

filling the water tank or if the machine

has been left on but not used for some

time.  Priming the machine ensures that

there is adequate water in the system for

its normal operation and failure to do

so could result in serious damage to your

machine.

•

 To prime your machine, position the

steam wand over the drip tray and fully

open the hot water / steam knob by

turning it counter clockwise.

• Wait until a steady stream of water comes

out of the steam wand and then close

the knob.

• Allow at least 4 oz. of water to flow

through the steam wand when priming

your machine.

PRE-HEATING

• Before brewing espresso you will want

to pre-heat both the filter holder and the

cup(s) you will use to serve your espres-

so. Use the following procedure.

•

 Make sure that the ready light is on

and then insert the filter holder, with

empty filter basket in place, into the brew

head of the machine. Turn the handle of

the filter holder from left to right until it

is securely in place. When you release

the handle it will automatically spring

slightly back to the left. This indicates that

the filter holder is operating properly.

• Place your cup(s) to be warmed directly

beneath the two outlets on the bottom

of the filter holder.

•

 Turn the brew switch on, the pump

will come on and after a few seconds

water will begin to flow into the cup(s).

Allow the water to flow until the cup or

cups are almost full then turn the brew

switch off.

Содержание TYPE SIN 017


















Отзывы: