Saeco Cafissimo HD8603, Руководство по эксплуатации

Страница: 15 / 23

• 27 •
Proceed as follows to set the desired quantity of frothed milk :
1- Insert the carafe into the machine and ensure that the milk is
above the MIN level.
2- Place a glass underneath the milk dispensing spout as indicated
in the section “Adjusting the dispensing height”.
3-
Press and hold the frothed milk button for 3 seconds until it
flashes in brief intervals. Then release the button.
4-
Press the frothed milk button again when the amount of
milk in the glass reaches the desired level.
At this point the frothed milk button has been reprogrammed.
Each time it is pressed, the machine will prepare the same amount
of frothed milk that was just programmed.
Minimum quantity of milk that can be set: approx. 50 ml
Maximum quantity of milk that can be set: approx. 300 ml
Preset quantities:
Frothed milk: approx. 110 ml
Restoring the preset quantities
To reset beverages to their factory settings, with the machine off,
press and hold the On/Off and filter coffee (blue) buttons
for 5 seconds. All buttons will flash twice in confirmation.
Latte macchiato
Before preparing a latte macchiato, check that the
On/Off button and beverage buttons are con-
stantly lit and that there is enough water in the tank.
We recommend approx. 130 ml frothed milk and 40 ml
espresso for a latte macchiato. If necessary, you can reset
the quantity of milk as described in the section “Adjusting
the amount of frothed milk” before preparing the beverage.
1-
Insert the carafe into the machine and ensure that the milk is
above the MIN level.
2-
Adjust the machine to fit the glass into which your latte mac-
chiato will be dispensed (see section “Adjusting the dispensing
height“).
3- Place a glass under the coffee and milk
dispensing spouts.
4- DO NOT insert a coffee capsule into the
capsule compartment.
5- Press the frothed milk button .
6- The frothed milk button flashes; the
machine is warming up.
7- When it has finished warming up, the
machine dispenses the frothed milk
directly into the glass. The machine
will stop dispensing when it reaches the preset quantity. The
dispensing process can be stopped early by pressing the frothed
milk button .
Fig. 1 Fig. 2 Fig. 3
Make sure there is enough space in the glass for the
coffee when dispensing the milk.
8- Lift the capsule compartment opening lever (Fig. 1) .
9- Insert the capsule as shown in the figure (Fig. 2) .
10- Lower the lever to close the capsule compartment (Fig. 3) .
11- Press the (white) button for an espresso, the (yellow)
button for a caffè crema or the (blue) button for a filter
coffee.
12-
The dispensing process stops automatically when the set
level is reached. However, it is possible to stop the dispensing
process early by pressing the same button as the beverage being
dispensed.
13-
Lift the lever to eject the used capsule into the used capsule
drawer.
14- Remove the glass from the grille.
Rinsing the milk circuit
To always ensure optimal hygiene, the milk circuit must be quickly
rinsed after use.
The user is reminded to do this by the rinse button lighting up.
It remains on until the circuit has been rinsed or the machine has
been turned off.
To rinse the milk circuit, proceed as follows:
1-
Ensure that the milk carafe is in the machine.
2-
Place a glass under the milk dispensing spout.
3-
Press the rinse button .
The machine dispenses a quantity of water sufficient to rinse the
milk circuit. Once finished, remove the glass.
Caution: The rinsing water is hot!
Finally, always remember to put the carafe with the remaining milk
in the refrigerator.
The rinse milk circuit function helps the machine to
maintain optimal hygiene conditions and service,
but in no case should it be considered sufficient as the only
way of cleaning the carafe and milk circuit.
Always clean the carafe as described in the chapter “Cleaning
and maintenance“.
English
4219_404_3749_2_148X210_BW_V8.indd 27 13/11/15 12:42