15
G
General notes
Our “General Terms and Conditions for Business“ together with the “General Conditions for the Supply of Products and Services of the Electrical
and Electronics Industry“ (ZVEI conditions) including supplementary clause “Extended Retention of Title“ apply as the exclusive terms and conditions.
In addition, the following points are to be observed:
– These instructions must be read before installation and putting in operation and all notes provided therein are to be regarded!
– Devices must only be connected to safety extra-low voltage and under dead-voltage condition. To avoid damages and errors the device
(e.g. by voltage induction) shielded cables are to be used, laying parallel with current-carrying lines is to be avoided, and EMC directives are to
be observed.
– This device shall only be used for its intended purpose. Respective safety regulations issued by the VDE, the states, their control authorities,
the TÜV and the local energy supply company must be observed. The purchaser has to adhere to the building and safety regulations and has to
prevent perils of any kind.
– No warranties or liabilities will be assumed for defects and damages arising from improper use of this device.
– Consequential damages caused by a fault in this device are excluded from warranty or liability.
– These devices must be installed by authorised specialists only.
– The technical data and connecting conditions of the mounting and operating instructions delivered together with the device are exclusively
valid. Deviations from the catalogue representation are not explicitly mentioned and are possible in terms of technical progress and continuous
improvement of our products.
– In case of any modifications made by the user, all warranty claims are forfeited.
– This device must not be installed close to heat sources (e.g. radiators) or be exposed to their heat flow. Direct sun irradiation or heat
irradiation by similar sources (powerful lamps, halogen spotlights) must absolutely be avoided.
– Operating this device close to other devices that do not comply with EMC directives may influence functionality.
– This device must not be used for monitoring applications, which solely serve the purpose of protecting persons against hazards or injury,
or as an EMERGENCY STOP switch for systems or machinery, or for any other similar safety-relevant purposes.
– Dimensions of enclosures or enclosure accessories may show slight tolerances on the specifications provided in these instructions.
– Modifications of these records are not permitted.
– In case of a complaint, only complete devices returned in original packing will be accepted.
These instructions must be read before installation and putting in operation and all notes provided therein are to be regarded!
THERMASGARD
®
9111 (fieldbus input modules)
THERMASGARD
®
9112 (fieldbus output modules)
Type ⁄ WG1
Item No.
Inputs
Features
FB -16E - L
1905-9111-1000-400
16 digital
with LEDs
FB - 8AE
1905-9111-2000-500
8 analog
for passive sensors
Pt100, Pt1000, Ni1000, Ni100TK5000
FB - 8AE - U
1905-9111-2010-500
8 analog
active 0 -10 V
FB - 8AE - I
1905-9111-2020-500
8 analog
active 4...20 mA
Type ⁄ WG1
Item No.
Outputs ⁄ Inputs
Features
FB - 8AA - U
1905-9112-0200-100
8 analog out
active 0 -10 V
FB - 8AA - U - H
1905-9112-0201 -100
8 analog out
active 0 -10 V
with manual operating level
FB - 8RA
1905-9112-0300-100
8 relay out
normally open contacts
FB - 8RA - H
1905-9112-0301 -100
8 relay out
normally open contacts
with manual operating level
FB - 8RA - 4AE
1905-9112-2300-300
8 relay out ⁄
normally open contacts ⁄
4 passive in
Pt100, Pt1000, Ni1000, Ni100TK5000
FB - 8RA - 4AE - H
1905-9112-2301 -300
8 relay out ⁄
normally open contacts ⁄
4 passive in
Pt100, Pt1000, Ni1000, Ni100TK5000
with manual operating level
FB - 8RA - 4AE - U
1905-9112-2310-300
8 relay out ⁄
normally open contacts ⁄
4 active in
0 -10 V
FB - 8RA - 4AE - U - H
1905-9112-2311 -300
8 relay out ⁄
normally open contacts ⁄
4 active in
0 -10 V
with manual operating level
