background image

5

I N S TA L L AT I O N   I N S T R U C T I O N S

T Y P I C A L   I N S TA L L AT I O N

1. 

Per NEC Article 680.23 (5) lights are to be installed in no less than 18” (450mm) below 
the normal water level unless the luminaire is listed and identified for use at lesser depths. 
S.R.Smith lights are listed and identified for use at depths no less than 4” (100mm) below the 
normal water level. Max depth is 36” below water surface.  All depth measurements are from 
the normal water level to the top of the Luminaire lens.

2. 

Fit an S.R.Smith LNS-2G, LNS-2A, LNS-2V or similar 1 1/2” pool wall fitting into the pool wall 
at the selected location. Watertight PVC conduit must be used from the wall fitting to the 
above water/ground level conduit termination on the equipment or supply side of the 12V 
AC line. Please refer to the illustration below.

3. 

Fit the S.R.Smith 

kēlo

 LED Light into the 1 1/2” wall fitting as shown and carefully pull the 

waterproof supply cable through. Carefully thread the S.R.Smith 

kēlo

 into the threads and 

turn clockwise and gently tighten until secure. DO NOT Over-tighten the light as damage 

may occur.  Connect the red / black wire conductors of the S.R.Smith 

kēlo

 to an approved, 

low voltage, class 2, Magnetic Type Power Source that complies with UL379 or an S.R.Smith 
poolLUX™ brand power supply as required by NEC or relevant local codes and ordinances. 

NOTE:

 Even though the housing gasket (between Wall Fitting and Light) can be replaced by a 

bead of silicon suitable for pool use, water will eventually fill the conduit so be sure the conduit is 
watertight and terminates above ground.

FOR STANDARD 1 1/2” WALL FITTINGS IN A POOLS OR SPA

Luminaire is listed and 

identified for use at 4” or 

more below the normal 

water level of the pool.

Optimal lighting coverage 

may be found at 10-12” 

below water level. 

Maximum depth is 36”

*Approved 12VAC 

Class 2 Power 

Source

 (see line #3 above)

1.5” watertight, underground 

PVC conduit back to 12VAC 

transformer.

All fittings should be glued and 

watertight.

*Minimum of 3.5” of straight, 

1.5” PVC conduit behind the 

wall fitting required prior to 

conduit reducer or bend.   

back gasket

pool deck

4”Min

18” 

NEC Article 
680.23(5)

Содержание kelo LED light









Отзывы: