background image

EMISSIONS MAINTENANCE SCHEDULE AND  WARRANTED PARTS LIST

Emissions Parts 

Inspect Before  

Clean Every 

Replace  

Clean Every 

Replace Every 

 

Each Use 

5 Hours 

Every 25 Hours   

25 Hours  

50 Hours 

 

 

 

or Yearly 

or Yearly

CATALYST MUFFLER ASSEMBLY ..................................................................................................................... X
AIR FILTER ASSY
  includes:
  Filter Screen ..................................................... X
FUEL TANK ASSY
  includes:
  Fuel Lines ........................ X
  Fuel Cap .......................... X
IgNITION ASSY
  includes:
  Spark Plug ........................................................................................ X
ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO 
THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s 
original emission level, please refer to the maintenance section below.

CALL

1-800-860-4050

www.ry

obitool

s.com

CALL US fIRST

For any questions about operating or maintaining your product,  

call the Ryobi

®

 Help Line!

Your product has been fully tested prior to shipment  

to ensure your complete satisfaction.

WARRANTY

Содержание RY52504

























Отзывы: