background image

15

MAINTENANCE

REPLACINg THE BAR AND CHAIN

See Figures 15 - 20.

WARNINg: 

To avoid possible serious injury, stop engine before re-
placing the bar, chain, or performing any maintenance 
operation.

  Remove the bar nut and drivecase cover.

  The bar contains a bar stud slot that fits over the bar stud. 

The bar also contains a chain tensioning pin hole which 
fits over the chain tensioning pin.  

   Place the bar onto the bar stud so that the chain tension-

ing pin fits into the chain tensioning pin hole.

   Fit the chain over the sprocket and into the bar groove.  

The cutters on the top of the bar should face toward the 
bar tip, in the direction of the chain rotation.  

   Replace  the  drivecase  cover  and  install  the  bar  nut.  

Tighten the bar nut finger tight only. The bar must be free 
to move for tension adjustment.

CHAIN 

TENSIONING SCREw

Fig. 19

BAR NUT

Fig. 0

   Remove all slack from chain by turning the chain tension-

ing screw clockwise, assuring that the chain seats into 
the bar groove during tensioning. 

   Lift the tip of the bar up to check for sag. Release the tip 

of the bar, and turn the chain tensioning screw 1/ turn 
clockwise. Repeat this process until sag does not exist.

   Hold  the  tip  of  the  bar  up  and  tighten  the  bar  nut  

securely.

   Chain is correctly tensioned when there is no slack on 

the underside of the bar, the chain is snug, but it can be 
turned by hand without binding.

 

NOTE:  If chain is too tight, it will not rotate. Loosen the 
bar nut slightly and turn adjusting screw 1/4 turn counter-
clockwise. Lift the tip of the bar up and retighten bar nut.

CHAIN 

ROTATION

BAR NUT

CHAIN

SPROCKET

Fig. 18

BAR

DRIVECASE

COVER

BAR NUT

CHAIN

Fig. 15

DRIVECASE

COVER

CHAIN 

TENSIONING PIN

BAR NUT

Fig. 16

BAR STUD SLOT

BAR STUD

CHAIN TENSIONING 

PIN HOLE

BAR

SPROCKET

Fig. 17

Содержание RY52504

























Отзывы: