Ryobi RWC-1350, Руководство по эксплуатации для владельца

Страница: 6 / 8

5
DESCRIPTION
e) Do not use a toothed or chain saw blade or segmented
diamond-coated disc with more than 10 mm wide slits. Such
accessory tools cause a kickback or loss of control over the
power tool.
f) Avoid cutting disc jams or excessive contact pressure. Do not
make any excessively deep cuts. Overloading the cutting disc
increases the stress and likelihood of tilting or jamming and
thus the possibility of kickback or breakage of the grinding
tool.
g) If the cutting disc jams or you stop working, switch the tool off
and hold it steady until the disc has completely stopped
turning. Never attempt to pull a rotating cutting disc out of a
cut. This could lead to kickback. Identify and remove the
cause of the jam.
h) Do not switch the power tool back on as long as it is in the
workpiece. Allow the cutting disc to reach its full speed before
you carefully continue the cut. Otherwise, the disc may jam,
jump out of the workpiece or cause kickback.
i) Support panels or large workpieces to reduce the risk of the
cutting disc jamming and causing a kickback. Large
workpieces can bend under their own weight. The workpiece
must be supported on both sides, namely in the vicinity of the
cut and also at the edge.
|) Be particularly careful when making "pocket cuts" into existing
walls or other obscured areas. The inserted cutting disc may
cut into gas or water pipes, electrical wiring or other objects
that can cause kickback.
1. ON/OFF switch
2. Handle
3. Dust extraction adapter
4. Upper guard
5. Lock nut
6. Cutting depth adjust knob
7. Lower guard
8. Auxiliary handle
9. Safety lock-out trigger
10. Spindle lock
11. Roller
12. Reducer
13. Centring flange
14. Backing pad
15. Lock nut spanner
16. Hand chisel
17. Union nut
SPECIFICATIONS
SUPPLEMENTARY NOTES
Approved cutting disc designs:
Diamond-coated, disc diameter 125mm, disc thickness max
2.2mm
ORIGINAL ACCESSORIES /AUXILIARY EQUIP-
MENT
Only use the accessories and additional equipment that are
specified in the operating instructions and are compatible with
the appliance.
BEFORE USE
Attaching the dust extraction adapter
• Push the pins of the dust extraction adapter (3) into the
recesses on the dust extraction connector.
• Lock the dust extraction adapter (3) by turning
• Loosen the union nut (17)
• Push the pipe of the extraction device far enough into the
opening on the union nut (17)
• Tighten the union nut (17) fully.
PACKAGE CONTENTS
Wall chaser x 1
Cutting discs (pre-fitted)x 2
Lock nut spanner x 1
Dust extraction adapter (pre-fitted)x 1
Reducer (for use with the dust extraction adapter and a dust extractor
Hose of ø32mm) x 1
Hand chisel x 1
Operating mannual x 1
OPERATION
Setting the groove depth
• L oosen the cutting depth adjust knob (6)
• Set the lower guard (7) to the desired depth.
• Tighten the cutting depth adjust knob (6).
Switching on and off (Fig. 1)
NOTE:
Always switch the appliance on before making contact
with the material, then apply it to the workpiece. The wall
grinder is equipped with an electronic smooth start The motor
starts with a delay.
Switching the appliance on:
• Whi le pressing the safety lock-out trigger (9), squeeze the
ON/OFF switch (1).
Switching the appliance off:
• Re lease the ON/OFF switch (1).
Attaching and setting the cut width of the diamond cutting
discs
• Lo osen the cutting depth adjust knob (6).
• Push the lower guard (7) upwards.
• Press the spindle lock (10) and hold it down.
• Use the lock nut spanner (15) to loosen the lock nut (5).
• Remove the lock nut (5).
• Set the desired cut width in accordance with the number of
backing pad (14). Ensure that the centring flange (13) is set in
place as the top backing pad (14) (Fig. 2).
230V ~ 50Hz
1350W
11000min
-1
0-30mm
8-26mm
125mm
4.2kg
Voltage
Power input
Max. speed
Cutting depth
Cutting width
Blade size
Net weight