manualshive.com logo in svg
background image

3

 

Arsenic, beryllium, chromates, cobalt and nickel in 

total 0.2 % of mass fraction;

 

Beryllium, chromates, cobalt, cadmium separately 

0.1 % of mass fraction;

 

Metallic compounds shall be calculated as the 

metal element and chromates as CrO3;

 

Free crystalline silicic acid (SiO2): 2 % of mass 

fraction.

SpecIfIcATIONS

Air sand blasting gun
Model

RA-SBG-B

Average air consumption

330 L/min @
6.3 bar (90 psi)

Maximum working pressure

6.3 bar (90 psi)

Weight

0.68 kg

Air inlet size

6.35 mm (1/4” BSP)

Air hose ID

9.52 mm (3/8”)

Hopper capacity

0.62 L

Abrasive media size

120~180 Micron 

(120~80 Mesh)

Abrasive media type

Glass fibre sand

Air quality

Oil-free compressed 

air

A-weighted sound pressure 

level

LpA: 86 dB(A), 

KpA=3dB

Sound power level

LwA: 97 dB(A), 

KwA=3dB

Vibration value

ah: 0.4 m/s

2

Uncertainty

K=1.5 m/s

2

Noise emission values are in accordance with EN 1265, 

and this air sand blasting gun noise level is tested at no 

load.
Vibration emission values are in accordance with EN  ISO 

20643.

 wARNING

The  vibration  level  specified  in  these  instructions  has 

been measured in accordance with a standardised 

measuring procedure specified in EN ISO 20643 and 

can be used to make equipment comparisons. The 

specified vibration emission value can also be used to 

make an initial exposure estimate.
The vibration level varies in accordance with the use 

of the compressed air tool and may be higher than 

the  value  specified  in  these  instructions  in  some 

cases. It is easy to underestimate the vibration load if 

the compressed air tool is used regularly in a certain 

manner.

INTeNDeD USe

The air sand blasting gun is intended to be used only by 

adults who have read and understood the instructions 

and warnings in this manual, and can be considered 

responsible for their actions.
The product is intended for removing metal surface 

contaminants, stains, rust, paint, oil, roughening/matting 

a surface, etc,. using abrasive materials.
Do not use the product for any other purpose.

ReSIDUAL RISkS

Even if you are operating this product in accordance 

with all the safety requirements, potential risks of injury 

and damage remain. The following dangers can arise in 

connection with the structure and design of this product:
1.  Dust and fumes generated when using the product 

can cause health defects.

 

Only work in sufficiently ventilated area.

 

Always wear a safety mask when using the product 

and keep other people far away from work area.

2.  Danger of injury and property damage caused by high 

speed sanding abrasive.

 

Wear appropriate personal protective equipment.

 

Prior to operation, protect other people and 

property in the work area from high speed sanding 

abrasive by providing barriers or shields.

ASSeMBLy

AIR SUppLy SeT Up

See figure 2.

 

Make sure the regulator is in the "off" position.

 

Connect the product to a quick coupler. Wrap the 

thread with thread seal tape.

 

Attach the air hose to the compressor's air outlet. Then 

connect the other end to the quick coupler attached to 

the product.

Содержание RA-SBG-B













Отзывы: