![background image](http://html.mh-extra.com/html/ryobi/pmc1217k/pmc1217k_operators-manual_1503682004.webp)
4 — English
UNPACKING
This product requires assembly:
Carefully remove the product and any accessories from
the box. All items listed in the
Includes
section must be
included at the time of purchase.
WARNING:
Items in this
Assembly
section are not assembled to
the product by the manufacturer and require customer
installation. Use of a product that may have been
improperly assembled could result in serious personal
injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create
accessories or attachments not recommended for use
with this product. Any such alteration or modification is
misuse and could result in a hazardous condition leading
to possible serious personal injury.
PRE-INSTALLATION TIPS
Be sure to read through all of the
ASSEMBLY
instructions
before beginning assembly and installation. Once the
misting tubes and couplers are cemented together, they
cannot be disassembled.
Position nozzles approximately 24 in. apart. Nozzles should
be angled slightly down rather than facing straight out.
If the area to be cooled is more than 12 feet deep, position
the nozzles facing toward the area. If the area is less than
12 feet deep, position the nozzles facing away from the
area.
Make sure all pieces are completely clean and free of
debris of any kind before assembly.
Determine the desired layout of your system and where
you will connect your water source. Lay out the entire
system to determine how you want to combine the
misting tubes with the couplers to achieve your desired
mist curtain.
ASSEMBLING THE MISTING KIT
See Figures 1 - 6 and Figure 13, pages 9 - 11.
Before applying PVC cement to any of the connections as
described in the steps below, make sure to read through
all the steps and verify that all items are positioned
as required. Once the misting tubes and couplers are
cemented together, they cannot be disassembled.
Assemble PVC misting tubes into sections for horizontal
and vertical use using couplers and couplers with nozzles.
NOTE:
The last coupler on the section meant for
horizontal use should be a coupler with nozzle. Remove
the nozzle and install the drain valve in its place. Do not
disassemble the drain valve.
Connect the vertical and horizontal sections together
using the elbow provided.
NOTE:
The coupler with nozzle intended for the drain
valve should be positioned at the end opposite the elbow.
Connect the hose adaptor to the end of the misting tube
assembly closest to the water source.
Connect the end plug to the end of the misting tube
assembly farthest from the water source.
Secure all connections with PVC cement as described in
Securing PVC Connections
below.
Allow at least 1 hour of drying time before connecting
water to the system to prevent leaks or clogging.
SECURING PVC CONNECTIONS
See Figures 7 - 8, page 10.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1 and wear protective gloves when
using PVC cement to assemble misting kit. Only use PVC
cement in a well-ventilated area away from open flames
or sparks and avoid breathing fumes. Failure to do so
could result in possible serious personal injury.
Once you have completely laid out your system and verified
the correct position of all items as described in
Assembling
the Misting Kit
, you are ready to secure the connections.
Apply PVC cement to the outside of the misting tube and
the inside of the coupler.
Insert the tube into the coupler and twist approximately
1/4 turn. This will help spread the cement and provide a
water-tight seal. Hold for 30 seconds to assure a good
bond.
ASSEMBLY
Содержание PMC1217K
Страница 23: ...NOTES NOTAS ...
Страница 24: ...NOTES NOTAS ...