background image

1

English

GENERAL POWER TOOL SAfETy WARNINGS

 

  

WARNING

Read all safety warnings and all instructions.

 

Failure  to  follow  the  warnings  and  instructions  

may result  in  electric shock, fire and/or serious 

injury.

Save  all  warnings  and  instructions  for  future 

reference.

The  term  "power  tool''  in  the  warnings  refers  to  your 

mains-operated (corded) power tool or battery-operated 

(cordless) power tool.

WORK AREA SAfETy

  Keep work area clean and well lit. 

Cluttered or dark 

areas invite accidents.

  Do  not  operate  power  tools  in  explosive 

atmospheres,  such  as  in  the  presence  of 

flammable  liquids,    gases  or  dust. 

Power  tools 

create sparks which may ignite the dust or fumes.

  Keep  children  and  bystanders  away  while 

operating a power tool. 

Distractions can cause you 

to lose control.

ELECTRICAL SAfETy

  Power  tool  plugs  must  match  the  outlet.  Never 

modify  the  plug  in  any  way.  Do  not  use  any 

adaptor  plugs  with  earthed(grounded)  power 

tools. 

Unmodified  plugs  and  matching  outlets  will 

reduce risk of electric shock.

  Avoid  body  contact  with  earthed  or  grounded 

surfaces,  such  as  pipes,  radiators,  ranges  and 

refrigerators.

 There is an increased  risk of electric 

shock if your body is earthed or grounded.

  Do  not  expose  power  tools  to  rain  or  wet 

conditions.

 Water entering a power tool will increase 

the risk of electric shock.

  Do  not  abuse  the  cord.  Never  use  the  cord  for 

carrying,  pulling  or  unplugging  the  power  tool. 

Keep  cord  away  from  heat,  oil,  sharp  edges  or 

moving parts.

 Damaged or entangled cords increase 

the risk of electric shock.

  When  operating  a  power  tool  outdoors,  use  an 

extension  cord  suitable  for  outdoor  use.

  Use  of 

a  cord  suitable  for  outdoor  use  reduces  the  risk  of 

electric shock.

  If  operating  a  power  tool  in  a  damp  location  is 

unavoidable, use a residual current device (RCD) 

protected supply. 

Use of an RCD reduces the risk of 

electric shock.

 

NOTE:

  The  term  ''residual  current  device  (RCD)'' 

may  be  replaced  by  the  term  ''ground  fault  circuit 

interrupter (GFCI)'' or ''earth leakage circuit breaker 

(ELCB)''.

PERSONAL SAfETy

  Stay  alert,  watch  what  you  are  doing  and  use 

common sense when operating a power tool. Do 

not use a power tool while you are tired or under 

the  influence  of  drugs,  alcohol  or  medication.

 A 

moment  of    inattention  while  operating  power  tools 

may result in serious personal injury.

  Use personal protective equipment. Always wear 

eye  protection. 

Protective  equipment  such  as  dust 

mask,  non-skid  safety  shoes,  hard  hat,  or  hearing 

protection used for appropriate conditions will reduce 

personal injuries.

  Prevent unintentional starting. Ensure the switch 

is in the off-position before connecting to power 

source and/or battery pack, picking up or carrying 

the tool.

 Carrying power tools with your finger on the 

switch or energising power tools that have the switch 

on invites accidents.

  Remove  any  adjusting  key  or  wrench  before 

turning  the  power  tool  on.

 A  wrench  or  a  key  left 

attached  to  a  rotating  part  of  the  power  tool  may 

result in personal injury.

  Do  not  overreach.  Keep  proper  footing  and 

balance at all times.

 This enables better control of 

the power tool in unexpected situations.

  Dress  properly.  Do  not  wear  loose  clothing  or 

jewellery.  Keep  your  hair,  clothing  and  gloves 

away from moving parts.

 Loose clothes, jewellery or 

long hair can be caught in moving parts.

  If devices are provided for the connection of dust 

extraction  and  collection  facilities,  ensure  these 

are  connected  and  properly  used.

  Use  of  dust 

collection can reduce dust-related hazards.

POWER TOOL USE AND CARE

  Do  not  force  the  power  tool.  Use  the  correct 

power tool for your application.

 The correct power 

tool  will    do  the  job  better  and  safer  at  the  rate  for 

which it was designed.

  Do not use the power tool if the switch does not 

turn  it  on  and  off.

 Any  power  tool  that  cannot  be 

controlled with the switch is dangerous and must be 

repaired.

Содержание LCDI1402













Отзывы: