![background image](http://html1.mh-extra.com/html/ryobi/ggs-3000/ggs-3000_owners-operating-manual_1505491009.webp)
8
ASSEMBLY
SPECIFICATIONS
ITEMS SUPPLIED (Fig. 1)
1. INSTALL THE INFEED MATERIAL FUNNEL (Fig. 2)
2. ASSEMBLE THE LEGS (Fig. 5)
a. 1 x infeed material hopper
b. 1 x infeed material funnel
c. 1 x main body
d. 1 x branch gauge
e. 1 x material discharge chute
f. 2 x legs
g. 1 x mulch collection catcher
h. 1 x bracket
i. 1 x connection rod
j. 2 x transport wheel
k. 2 x wheel cover
230V~50Hz
2200W/3HP
2900rpm
Cone cutter, Self-feeding
Double sided reversible replacement
40mm
10:1
50kg
Voltage:
Power input:
No load speed:
Cutting system:
Blades:
Branch diameter:
Mulching ratio:
Net weight:
You will need:
6pcs M5x12 one-way screws;
6pcs M5 nylock nuts and 6pcs M5 flat washers
OPERATION
INFORMATION ON SHREDDING
1. Best operating results are obtained by feeding branches
and leaves together as the branch material helps to draw
leaves and other small materials through the machine.
2. Feed material branches at a constant speed to get an
even and consistent load avoid pushing large volume of
material at one time as this tends to clog the machine or
may create overload (May even trip the overload
protection switch).
3. If you want to just process leaves, we suggest best
results are achieved with the use of a push stick to help
push the leaves through the safety bristles at the bottom
of the plastic hopper.
4. The machine can shred chip green or dried branches and
leaves. However avoid wet material as these tend to stick
to the machine and may not feed efficiently.
(1) Align the slot in the funnel & protrusion in the main
body to locate the funnel in the right position. (Fig. 3)
(2) Screw the funnel to the main body (c) as shown.
(Fig. 4)
You will need:
2pcs M6 nylock nuts and 2pcs M6 flat washers;
2pcs M10 nylock nuts and 2pcs M10 flat washers;
2pcs M6x25 bolts
(1) Take the wheel cap from the wheel;
(2) Mount the wheel to the legs (left & right wheels);
(3) Fix the connection rod to the legs as shown.
3. INSTALL THE LEG ASSEMBLY (Fig. 6)
You will need:
4pcs M6 hexagon socket cap head screws;
4pcs M6 spring and 4pcs M6 flat washers
(1) Turn the machine upside down so the legs hole is
upward.
(2) Screw the leg assembly together with the bracket to
the main body as shown.
4. ASSEMBLE THE INFEED MATERIAL HOPPER
You will need:
6pcs M5x12 one-way screws;
6pcs M5 Nylock nuts and 6pcs M5 flat washers
(1) Align the slot & protrusion firstly to help you assemble
the hopper to the funnel. (Fig. 7)
(2) Screw the hopper to the funnel as shown by using 6
one-way screws. (Fig. 8)
(1) Screw the branch gauge to the material discharge
chute as shown by using 2 M5x10 screws. (Fig. 11)
5. ASSEMBLE THE MATERIAL DISCHARGE CHUTE
6. ASSEMBLE THE BRANCH GAUGE
You will need:
4pcs M6x14 one-way screws
You will need:
2pcs M5x10 screws;
(1) Mount the discharge chute; (Fig. 9)
(2) Screw it as shown. (Fig. 10)
7. FIT THE MULCH COLLECTION CATCHER
(Fig. 12)
(1) Open the wire inside of the catcher;
(2) Slide to assemble the catcher as shown.
Note:
the one-way screw could not be disassembled
once you mount it.
5. Branches become harder to shred depending on the type,
age and dryness of the wood. For best results, shred
fresh branches soon after they have been cut.
6. Soft garden waste should be shredded in smaller loads,
particularly for wet waste. Any blockages can be avoided
by intermittently shred branches.
7. If the motor stalls due to overloading or other cause turn
off the power switch and disconnect the shredder from
power source. Then unscrew the locking knob and open
the cutting chamber to clean the blockage inside. Before
opening the chamber, Please make sure that the motor
has been totally stopped.
Содержание GGS-3000
Страница 2: ...1 Allen key 4 11 6 8 1 12 2 5 9 10 7 3...
Страница 6: ...5 15 14 16 17 Fixed pin 40mm 40mm...
Страница 12: ......