![background image](http://html1.mh-extra.com/html/ryobi/ggs-3000/ggs-3000_owners-operating-manual_1505491008.webp)
7
INSTRUCTIONS FOR SAFE HANDLING
1. Make sure that the tool is only connected to the
voltage marked on the name plate.
2. Never use the tool if its cover or any bolts are missing.
If the cover or bolts have been removed, replace
them prior to use. Maintain all parts in good working
order.
3. Always secure tools when working in elevated
positions.
4. Never touch the blade, drill bit, grinding wheel or other
moving parts during use.
5. Never start a tool when its rotating component is in
contact with the workpiece.
6. Never lay a tool down before its moving parts have
come to a complete stop.
7.
ACCESSORIES:
The use of accessories or
attachments other than those recommended in these
instructions might present a hazard.
8.
REPLACEMENT PARTS:
When servicing use only
identical replacement parts.
SPECIFIC SAFETY RULES FOR GARDEN
SHREDDER
10. Avoid wearing loose fitting clothing, hanging cords or
ties.
11. Only operate the machine in open space (e.g. not too
close to a wall or other fixed objects) and on a firm, level
surface.
12. Do not operate the machine on paved or gravel surface
where ejected material could cause injury.
DESCRIPITION
10. Disc lock for blade changing
11. Motor block adjusting hole
12. Branch gauge
1. During operation, do not open the cutting chamber. The
machine runs on for a few seconds after being switched
off.
2. Never allow children or people unfamiliar with these
instructions to use the machine. When not in use store
the machine out of reach of children.
3. This tool is not intended for use by persons (including
children) with reduced physical sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
4. Before switching on, the machine must be assembled
according to the enclosed instructions.
5. Use only extension cables that are intended for outdoor
use and are protected against splashes of water.
6. Do not touch the plug or socket with wet hands.
7. Do not run over, crush or pull the power supply cable or
extension lead, otherwise, it may be damaged. Protect
the cable from heat, oil and sharp edges.
8. Other persons and animals should remain at a distance
of 3 metres or more when the machine is being used. The
operator is responsible for third persons in the working
area.
9. Become familiar with the instruction manual before
attempting to operate this machine.
13. Before starting the machine, check that all screws, nuts,
bolts and other fasteners are properly secured and that
guards and screens are in place.
14. Keep proper balance and footing at all times. Do not
overreach. Never stand at a higher level than the base
of the machine when feeding material.
15. When feeding material into the machine be extremely
careful that pieces of metal, rocks, bottles, cans or other
foreign objects are not included.
16. If the cutting mechanism strikes any foreign object or if
the machine should start making any unusual noise or
vibration, immediately switch off and allow the cutter
to stop. Remove the plug from the mains supply and
take the following steps:
- Inspect for damage.
- Inspect for damage.
- Check for and tighten any loose parts.
17. If the machine becomes clogged, switch off and allow
the cutter to stop. Remove the plug from the mains
supply before clearing debris.
18. Check if guards and protective devices are undamaged
and properly mounted. Beforeusing, carry out possibly
necessary maintenance and repairs.
19. Keep the motor cooling vents clean of debris and other
accumulations to prevent damage to the motor or
possible fire.
20. Never pick up or carry the machine while the motor is
running.
21. Switch off, allow the cutter to stop and re move the plug
from the mains supply whenever you leave the work
area.
22. Do not tamper with the power source governor settings.
Contact an approved service agent if a problem exists.
23. Do not tilt the machine while it is running.
24. Do not expose the machine to rain. Only store the
machine in a dry place.
1. Infeed material hopper
2. Infeed material funnel
3. Material discharge chute
4. Mulch collection catcher
5. Cut chamber locking knob
6. Transport wheels
7. ON/OFF switch
8. Overload protection switch
9. Patented cutter assembly: including blades
Содержание GGS-3000
Страница 2: ...1 Allen key 4 11 6 8 1 12 2 5 9 10 7 3...
Страница 6: ...5 15 14 16 17 Fixed pin 40mm 40mm...
Страница 12: ......