![background image](http://html.mh-extra.com/html/ryobi/ert-2100v/ert-2100v_user-manual_1505767024.webp)
OPERATION
WARNING
Never pull router out of work and place upside
down on work surface before the cutter stops.
CONNECTING A DUST EXTRACTOR (Fig. 16).
The dust extractor hose can be connected to the dust
extraction channel.
FINE HEIGHT ADJUSTER (31)
It is used to precisely control the depth of the cutter.
■
To use the fine height adjuster, ensure that the plunge
lock is released.
■
Rotate the knob clockwise to raise the cutter,
anticlockwise to lower the cutter.
■
When the desired position is reached, re-engage the
plunge lock before use.
LIVE TOOL INDICATOR (32)
This tool features a live tool indicator which illuminates as
soon as the tool is connected to the supply. This warns
the user that the tool is connected and will operate when
the switch is pressed.
MAINTENANCE
WARNING
When ser vicing use only identical Ryobi
replacement parts. Use of any other parts may
create a hazard or causeproduct damage.
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc.
WARNING
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.
come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
Electric tools used on fiberglass material, wallboard,
spackling compounds, or plaster are subject to acelerated
wear and possible premature failure, as the fiberglass
chips and grindings are highly abrasive to bearings,
brushes, commutators, etc. Consequently, we do not
recommended that this tool be used for extended work on
these types of materials. If, however, you do work with any
of these materials, it is extremely important that you clean
the tool frequently by blowing it with an air jet.
WARNING
Always wear safety goggles or safety glasses
with side shields during power tool operation or
when blowing dust. If operation is dusty, also
wear a dust mask.
LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life of the
unit under normal operating conditions. Therefore,
no further lubrication is required.
CUTTERS
Get faster and more accurate cutting results by keeping
cutters clean and sharp. Remove all accumulated pitch
and gum from cutters after each use.
When sharpening cutters, sharpen only the inside of the
cutting edge. Never grind the outside diameter. Be sure
when shar pening the end of a cutter to grind the
clearance angle the same as originally ground.
COLLET
Dust and chips may collect on the collet from time to time,
making it necessary to clean the collet. To do so, remove
the collet assembly and wipe it with a clean dry rag.
Clean the taper in the shaft in the same manner. Never
immerse the collet or end of the shaft in a solvent or in
water. Before replacing the collet assembly, put a drop of
motor oil on the inside of the nut, on the threads of the
shaft, and on the taper in the shaft. Replace the collet
assembly onto the shaft by hand only. Never tighten the
collet nut without a bit in the collet. This action could
permanently damage the collet.
BRUSH ASSEMBLIES (Fig. 19)
Your router has externally accessible brush assemblies
(35) that should periodically be checked for wear.
To replace brush assemblies:
■
UNPLUG YOUR ROUTER.
WARNING
Failure to unplug your router could result in
accidental starting causing serious injury.
18
GB
English
F
D
E
I
P
NL
S
DK
N
FIN
GR
H
CZ
RUS
PL
RO
SLO
TR
HR
ERT-2100V_20 lgs 2/6/2004 7:34 PM Page 18
Содержание ERT-2100V
