![background image](http://html1.mh-extra.com/html/ryobi/ehg-2002c/ehg-2002c_user-manual_1505741009.webp)
SAFETY RULES
■
Disconnect the heat gun when it is not in use. Ensure
that the heat gun cannot start accidentally. If the heat
gun stops while it is in use, disconnect it from the
power supply and have it serviced by authorised
service center.
WARNING
Always concentrate on the job and use common
sense when working with this or any other tools.
Do not use this tool when you are tired or taking
medication that may make you drowsy.
NB: Keep the nozzle at least 10 cm away from the
working surface. Heat guns have a safety cut-off
which will stop the heat gun if you are working too
close to the surface being stripped. If the cut-off
operates, the hot air gun must be allowed to cool for
about 30 minutes before it can be used again.
■
Never use the heat gun in combination with solvents.
■
After use, remove any paint or varnish residue on the
nozzle and scrappers. This could catch fire.
■
Always work in a well ventilated area. Flakes and
residues of lead-based paints are highly toxic.
POWER SUPPLY
Ensure that the power supply corresponds to the rating
plate on the heat gun. The power supply should be 230V
50Hz AC (normal mains). Voltage deviation greater than
10% may cause loss of power and possible overheat.
For greater safety, the heat gun is double insulated.
This means that there are two separate insulation
systems between the user and the live elements of
the heat gun.
WARNING
Although the heat gun is double insulated,
normal safety precautions should be taken when
using the heat gun to avoid injury that may be
caused by a failure of the electrial installation
inside the equipment. This tools are not designed
to be earthed. The heat gun power cable is,
therefore, fitted with a two pin plug for use in
normal 230V power sockets.
SPECIFICATION
Model No.
EHG-2002C
Rating
2000W
Voltage
230V
Frequency
50Hz
Temperature
60 / 600ºC
Air flow
250 or 500 l/min
Variable temperature adjust
No
LED temperature indicator
No
LCD temperature indicator
No
Model No.
EHG-2002LED
EHG-2002LCD
Rating
2000W
2000W
Voltage
230V
230V
Frequency
50Hz
50Hz
Temperature
50 - 550ºC/ 50 - 650ºC
Air flow
250 or 500 l/min
Variable temperature adjust
Yes
Yes
LED temperature indicator
Yes
No
LCD temperature indicator
No
Yes
DESCRIPTION
1.
Accepts accessory nozzles
2.
Guard sleeve
3.
Variable temperature control
(For EHG-2002LED/ LCD only)
4.
Switch
5.
Hanger & support stand
6.
LED temperature indicator (For EHG-2002LED only)
7.
LCD temperature indicator (For EHG-2002LCD only)
USING THE HEAT GUN
The heat gun is very easy to use. Before plugging the heat
gun in, always ensure that the switch is set to 0 (OFF).
When you are ready, adjust the switch (4)
to setting1 or 2. Always allow the heat gun to warm up for
at least 1minute to reach to operating temperature.
Always wear gloves and eye protection. The heat gun has
a built-in stand to keep it upright on a flat horizontal
surface. This leaves both hands free for softening PVC
pipes or other material. Always keep your hands away
from the nozzle.
6
GB
F
D
E
English
I
P
NL
S
DK
N
FIN
GR
H
CZ
RUS
RO
PL
EHG-2002C manual 19/08/04 11:12 Page 6
Содержание EHG-2002C
Страница 2: ...Fig 2 Fig 4 Fig 3 Fig 5 1 2 4 5 3 Fig 1 2 1 0 2 1 0 6 7 EHG 2002C manual 19 08 04 11 12 Page A2...
Страница 43: ...40 GR F GB D E I P NL S DK N FIN H CZ RUS RO PL EHG 2002C manual 19 08 04 11 12 Page 40 0 063 j0 039...
Страница 55: ...52 RUS F GB D E I P NL S DK N FIN GR H CZ RO PL EHG 2002C manual 19 08 04 11 12 Page 52 0 063 j0 039...