Ryobi BTS211 Скачать руководство пользователя

Страница: 26 / 42

OPERATION



Retighten hex nut, securing eccentric screw and quick-

stop.



Check your work. If the quick-stop is not at zero degrees,

repeat above steps.

wARNING:

To reduce the risk of injury, always make sure the rip fence
is parallel to the blade before beginning any operation.

TO SET THE RIP FENCE SCALE INDICATOR
TO THE bLADE

See Figure 29.

Begin with the blade at a zero angle (straight up).



Unplug the saw.



Raise the blade guard.



Loosen the rip fence by lifting the locking lever.



Using a framing square, set the rip fence 2 in. from the

blade tip edge.



Loosen the screw on the scale indicator and align with

the 2 in. mark as shown.



Tighten the screw and check the dimension and the rip

fence.

TO USE THE RIP FENCE

See Figure 30.



Place the rear lip on the rear of the saw table and pull

slightly toward the front of the unit.



Lower the front end of the rip fence onto the guide

surfaces on top of the front rail.



Push the locking lever down to automatically align and

secure the fence.

Check for a smooth gliding action. If adjustments are needed,
see

To Check the Alignment of the Rip Fence to the blade

in the

Adjustment

section of this manual.

Fig. 30

rear liP

riP Fence

locKinG

leVer

saW

taBle

2 in.

Front

rail

locKinG

leVer

Blade

riP

Fence

2 in.

marK

scale

indicator

Fig. 29

quicK

stoP

Fig. 28

Содержание BTS211











































Результаты поиска

Содержание BTS211

Отзывы:

Похожие инструкции для BTS211

Бренды по названию

Популярные бренды

Ryobi BTS211, Руководство оператора

Результаты поиска

Содержание BTS211

Отзывы:

Похожие инструкции для BTS211

Бренды по названию

Популярные бренды