Ryobi BTS211 Скачать руководство пользователя | Manualshive

Страница: 19 / 42

background image

19

ASSEMbLy

TO INSTALL bLADE GUARD ASSEMbLy

See Figure 14.

Proper installation of the blade guard assembly means that
the saw blade and spreader are in alignment. ALWAYS align
the spreader to the saw blade prior to turning on the table
saw.



Lower the blade.



Loosen the wing nut and slide the spreader between the

mounting plate and flat washer. Partially retighten the
wing nut.



Check the blade and spreader alignment.

NOTE: Blade alignment with the spreader can be

adjusted for different blade widths. Refer to:

To Check,

and Align the Spreader, Saw blade, and blade Guard
Assembly in the

Adjustment

section. Check the blade

guard assembly for clearances and free movement.



Tighten wing nut securely.

NOTE: If the wing nut and washers are completely removed,

reinstall in the following order: flat washer, star washer, and
wing nut.

TO INSTALL DUST bAG

See Figure 15.



Slide the elbow inside the dust chute on the back of the

table saw.



Slide the dust bag into the elbow.

NOTE: For efficient operation, empty the dust bag before it

is half full. This will permit better air flow through the bag.

OPERATION

wARNING:

Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is suf-
ficient to inflict severe injury.

wARNING:

Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.

Fig. 14

mountinG

Plate

WinG

nut

sPreader

anti-KicKBacK

PaWls

Fig. 15

dust

BaG

dust

cHute

elBoW

Flat

WasHer

star WasHer

WinG nut

«
...
17
18
19
20
21
...
»

Содержание BTS211











































Отзывы:

Нет отзывов

Похожие инструкции для BTS211

Бренд: ATIKA Страницы: 141

TILE MAGIC TMG-851

Бренд: Felker Страницы: 20

Бренд: Delta Страницы: 12

Бренд: Asada Страницы: 28

Бренд: Hilti Страницы: 17

ALITEC PS9 1.5HD SINGLE CIRCUIT

Бренд: Woods Страницы: 40

Бренд: Ryobi Страницы: 28

Бренд: AEG Страницы: 36

PowerTools BKS 18BL

Бренд: AEG Страницы: 58

Бренд: AEG Страницы: 79

Бренд: AEG Страницы: 104

Бренд: AEG Страницы: 35

Бренд: AEG Страницы: 28

POWERTOOLS KS 55-2

Бренд: AEG Страницы: 101

Бренд: AEG Страницы: 114

Бренд: AEG Страницы: 106

Бренд: AEG Страницы: 148

Бренд: AEG Страницы: 115

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды