Ryobi BTS16 Скачать руководство пользователя

Страница: 36 / 40

ADJUSTMENTS

Fig. 49

Blade

riP FenCe

loCKinG

leVer

SCreWS

Fig. 48

loCK nut

KnoB

Miter

GauGe BaSe

45° adJuStaBle

StoP SCreW

0° adJuStaBle

StoP SCreW

Miter

GauGe rod

TO ADJUST THE MITER GAUGE

See Figure 48.

You can set the miter gauge at 0° and plus or minus 45° with
the miter gauge stop pin and adjustable stop screws.

NOTE:

The miter gauge provides close accuracy in angled

cuts. For very close tolerances, test cuts are recommended.



Loosen knob and pull out on stop pin to rotate miter

gauge base past stop screws.



Loosen the lock nut of the 0° stop screw at the stop pin

with a 8 mm wrench.



Place a 90° square against the miter gauge rod and the

miter gauge base.



If the rod is not square, loosen the knob, adjust the rod,

and tighten the knob.



Adjust the 0° stop screw until it rests against the stop

pin.



Adjust the plus and minus 45° stop screws using a 45°

triangle and the steps above.

TO CHECK THE ALIGNMENT OF THE RIP
FENCE TO THE bLADE

See Figure 49.



Unplug the saw.



Raise the locking lever to permit the rip fence to be

moved.



Place a framing square beside the blade and move the

rip fence up to the square. Take the dimension on the rip
scale.



Move the fence back and turn the framing square 180°

to check the other side.



If the two dimensions are not the same, loosen the two

screws on the fence and align it.



Retighten the two screws.



Make two or three test cuts on scrap wood. If the cuts

are not true, repeat the process.

wARNING:

Before plugging the saw back in to make test cuts, make
sure the switch is in the

OFF position and the blade guard

is in place. Failure to do so can result in serious injury.

Содержание BTS16









































Результаты поиска

Содержание BTS16

Отзывы:

Похожие инструкции для BTS16

Бренды по названию

Популярные бренды

Ryobi BTS16, Руководство оператора

Результаты поиска

Содержание BTS16

Отзывы:

Похожие инструкции для BTS16

Бренды по названию

Популярные бренды