Ryobi AP13AK Скачать руководство пользователя страница 4

Страница: 4 / 14

RULES FOR SAFE OPERATION

Page 3

Power

Switch

Table

Extention

Depth Scale

Hand Crank

Stock Rollers

Overload

Switch

Always wear eye protection when operating the

machine.
Check to make sure all holding screws are tight

before starting machine.
Always stop the motor and disconnect from power

source before making any adjustments.
Be sure all guards are in place before operation.
Read owner’s manual thoroughly and familiarise

yourself with the machine before operation.
Do not force work through the machine. Allow the

planer to apply the proper feed rate.
Check feed rollers occasionally to be sure

sawdust and chips are not lodged between any

components. If rollers are not seated firmly, the

feed rolls will not hold timber firmly against the

bed, allowing kickback.
Only plane wood boards.
Use sound timber, with no loose knots and as few

tight knots as possible.
Never stand directly in line with either the infeed

or outfeed sides. Always stand off to one side of

the machine.

Make sure the workpiece is free of from nails,

screws stones and other foreign objects which

could damage the blades.
Make sure the blades are attached correctly as

described in the instructions.
Use caution when handling the blades and

cutterhead assembly. The blades are sharp and

can easily cut your hand.
Allow the cutterhead to reach full speed before

using.

Содержание AP13AK















Результаты поиска

Содержание AP13AK

Отзывы:

Похожие инструкции для AP13AK

Бренды по названию

Популярные бренды

Ryobi AP13AK, Руководство по эксплуатации для владельца

Результаты поиска

Содержание AP13AK

Отзывы:

Похожие инструкции для AP13AK

Бренды по названию

Популярные бренды