Russell Corporation M85544C Скачать руководство пользователя

Страница: 19 / 19

10/05

ID# M85544C

Subject to proper installation and normal use, Hydra-Rib

warrants, subject to limitations below, to the original retail

purchaser all structural components of the Hydra-Rib

system to be free of defects in material and workmanship

for the duration of ownership by the original retail

purchaser.

Merchandise must be shipped prepaid with a copy of proof

of purchase to our factory for examination to see whether

it needs to be repaired or replaced. Any labor costs,

travel expenses and any other charges involved in the

removal, installation or replacement of the

defective/repaired parts from/to your Hydra-Rib

system

will be your (the purchaser’s) responsibility. Shipping

charges for replaced or warranted merchandise being

sent back to the customer from our factory must be

prepaid by the customer in advance. If not, the

replacement shipment will be sent out collect.

What is Not Covered By This Warranty

Paint or rusted parts. Paint kits will be available to assist in

normal maintenance.

RIM

HANGING ON THE RIM WILL VOID YOUR WARRANTY.

RIms are not warranted for any defects other than

workmanship. Torn back plates, damaged springs, bent

rings, damaged eye bolts, and torn or distorted rim

supports result from hanging on the rim and are not

warranted.

LIMITED LIFETIME WARRANTY

Содержание M85544C




















Результаты поиска

Содержание M85544C

Отзывы:

Похожие инструкции для M85544C

Бренды по названию

Популярные бренды

Russell Corporation M85544C, Руководство пользователя

Результаты поиска

Содержание M85544C

Отзывы:

Похожие инструкции для M85544C

Бренды по названию

Популярные бренды