RUPTELA FM-Pro 4 BT Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 37

RUPTELA FM-Pro 4 BT Скачать руководство пользователя страница 7

3

Device description

3.1

About

Ruptela‘s FM-Pro4 / Pro4 3G / Pro4 BT is 4

th

generation advanced, low power consumption but powerful

tracking device. It acquires it’s position by a GPS/GLONASS signal and transfers data to a server via cellular

3G or GSM/GPRS network.
3G network support was not previously available for FM4 devices. This new feature in FM-Pro4 3G is the

main advantage over the FM-Pro4 devices.
FM-Pro4 BT device contains Bluetooth module. This feature further extends its accessories list and adds

new configuration capabilities.
Some common FM-Pro4 / Pro4 3G / Pro4 BT advantages over previous generation FM-Pro3 devices:

Lower power consumption

More powerful 1-wire interface

USB power supply for configuration

2 x RS232 and 1 x RS485 ports work at the same time

2 SIM card slots (on demand, only for FM-Pro4 / Pro4 BT)

Gyroscope (on demand)

FM-Pro4

FM-Pro4 3G

FM-Pro4 BT

3.2

Package contents

FM-Pro4 / Pro4 3G / Pro4 BT device is supplied in cardboard package. GPS/GLONASS antenna and IO

cables are disconnected from device. Package contents:

FM- Pro4 / Pro4 3G / Pro4 BT device

12 PINs and 14 PINs cables

GPS/GLONASS all-in-one antenna

«
...
5
6
7
8
9
...
»

Содержание FM-Pro 4 BT






































Отзывы:

Нет отзывов