Ruijie Networks RG-WALL1600-S3600 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 28

Ruijie Networks RG-WALL1600-S3600 Скачать руководство пользователя страница 11

·

Chapter 3 Product Installation

RG-WALL1600-S3600 must be used and fixed in the room.

Make sure you have carefully read part 2 and this part, and be sure that the requirements set forth in part 2
have been met.

Installation Procedure

Installation Verification

The RG-WALL1600-S3600 is complicated equipment, so you must carefully plan and arrange the installation location,
networking mode, power supply, and wiring before installation. Verify the following before installation:



The installation location is of a good air flow.



The installation location meets the temperature and humidity requirements of the equipment.



The qualified power supply is available at the installation location.



The related network cables have already been deployed at the installation location.



The selected power supply meets the system power.

Preparation

Install the Cabinet (Optional)

Mount chassis into cabinet (Optional)

Ground the system

Insert various modules

Connect cables or fibers to ports

Bind cables or fibers

Verification

End

Connect power supply

«
...
9
10
11
12
13
...
»

Содержание RG-WALL1600-S3600





























Отзывы:

Нет отзывов