Ruby Tech ES-2410C Скачать руководство пользователя страница 18

Страница: 18 / 291

Publication date: Jan., 2009
Revision A1

2. Installation

2-1. Starting ES-2410C Up

This section will give users a quick start for:

Hardware and Cable Installation

- Management Station Installation

- Software booting and configuration

2-1-1. Hardware and Cable Installation

At the beginning, please do first:

⇒

Wear a grounding device to avoid the damage from electrostatic discharge

•

Installing Optional SFP/GBIC

Fiber Transceivers to the ES-2410C L2 Plus

Managed Switch

Note: If you have no modules, please skip this section.

•

Connecting the SFP/GBIC Module to the Chassis:

The optional SFP/GBIC modules are hot swappable, so you can plug or unplug
it before or after powering on.

1. Verify that the SFP/GBIC module is the right model and conforms to the
chassis

2. Slide the module along the slot. Also be sure that the module is properly

seated against the slot socket/connector

3. Install the media cable for network connection

4. Repeat the above steps, as needed, for each module to be installed into

slot(s)

5. Have the power ON after the above procedures are done

Fig. 2-1 Installation of Optional SFP/GBIC Fiber Transceiver

Содержание ES-2410C




































































































































































































































































































Результаты поиска

Содержание ES-2410C

Отзывы:

Похожие инструкции для ES-2410C

Бренды по названию

Популярные бренды

Ruby Tech ES-2410C, Руководство пользователя

Результаты поиска

Содержание ES-2410C

Отзывы:

Похожие инструкции для ES-2410C

Бренды по названию

Популярные бренды