background image

MEMS Tilt Beam Instruction Manual 

RST Instruments 

 

2  MATERIALS 

2.1  R

EQUIRED 

T

OOLS

/C

OMPONENTS

 

Before beginning the installation of the Horizontal or Vertical MEMS Tilt Beam, 
ensure that all of the components and tools required for installation are present. See 
the list below for tools and equipment required for a typical installation: 

 

 MEMS Tilt Beam(s) 

 (1) Readout (IC6800-V,  or FlexDaq 1000/800 Datalogger) 

 (1) Level 

 (1) Phillips screw driver 

 (1) Anchor kit (consisting of (2) 10mm SS anchors, (4) belleville washers, (4) nylon 

washers, (2) nylon bushing, (4) 10mm SS nuts  

 (2) 16mm wrench 

 
 

3  INSTALLATION 

Determine the MEMS Tilt Beam installation location. The location must allow for 
access inside the beam to connect the sensors after the unit has been mounted. The 
mounting angles should be securely attached with the supplied hardware to a rigid 
structure that is free of vibration. Care should be taken to avoid areas of rapid or 
extreme changes in temperature such as direct sunlight or near heating or cooling 
equipment. For exposed units, a sun shade and or external insulation is 
recommended.  

 

The output of the MEMS sensor(s) is in Volts, which can be read with an RST IC6800-
V Readout or a FlexDaq 1000/800 Datalogger.  The MEMS sensors have excellent 
zero and full scale stability. As a result, precision sensor zeroing is not necessary. 
This is in contrast to electrolytic sensors which have high coefficients of thermal 
sensitivity, necessitating precise leveling on the structure. 

 

3.1  A

NCHOR 

I

NSTALLATION

 

It is important to install the anchors at a distance equal to the MEMS Tilt Beam 
mounting angles pattern (using a level, ensure the anchors are installed inline 
horizontally or vertically) (see figure 3). 

 

The anchors should: 

1.  Protruding horizontally, in all planes, from the structure (not necessarily 

perpendicular to the structure) 

Содержание MEMS Tilt Beam

















Отзывы: