RR Mechatronics EHST109621 страница 23 Скачать руководство пользователя

Страница: 23 / 134

Starrsed program

The Interrliner is controlled via an external computer on which runs the Starrsed software. The software

functions are grouped on six tabbed screens. The software is controlled by mouse pointer or directly via the

touch screen. A virtual keyboard is automatically displayed on screen, when numerical or alphanumerical

input is required.
Normal operational screens are the

Sample

and the

History

screen.

The

Reagents

screen is used to check the reagent levels and log reagent replacement.

To activate priming sequences and cleaning operations, the screen

Maintenance

is used.

The

Settings

and

Service

screens are protected by a password to prevent accidental change of settings. The

Service

menu is used for service and control purposes.

Note

: In the next sections move the mouse over the tab and click the left mouse button. Click again

on the same tab for detailed information on the subject.

Starrsed program

MRN-164_2-EN Version 2.02 Interrliner

Содержание EHST109621







































































































































Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды

RR Mechatronics EHST109621, Инструкция по эксплуатации

Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды