RR Mechatronics EHST109621 Скачать руководство пользователя

Страница: 30 / 134

5.3 - History screen

In History the following options can be selected:

▪

Display pipette data

Use button

Print

to send the selected data to the printer.

▪

Display sample history

▪

Display full patient result

In Display sample history are the following options available:

Print

: Send the selected result to the printer.

Print result header

: Only if option Settings - General settings "

Print after measurement

" is switched

it is

possible to print a result header.

Send all to HOST

: Send all results again to the

HOST

Send patient result to HOST

: Send only the selected patient result to the

HOST

▪

Display rack history

▪

Display rack details

▪

Analyse results

▪

ESR Statistics

▪

QC Results

(with Starrsed Control)

▪

Linked QC IDs

Starrsed program

MRN-164_2-EN Version 2.02 Interrliner

Содержание EHST109621







































































































































Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды

RR Mechatronics EHST109621, Инструкция по эксплуатации

Результаты поиска

Содержание EHST109621

Отзывы:

Похожие инструкции для EHST109621

Бренды по названию

Популярные бренды