ROYAL HT88 PAPER SHREDDER
Paper jams and overload protection:
HT88 is equipped with a motor overload protection device. The normal short duty
cycle for continuous shredding at maximum capacity is 2 minutes on and 4 minutes
off. The power may terminate automatically in case of the following abnormal situations:
1. Operating the shredder at the maximum capacity continuously for a
prolonged period of time, eg. more than 2 minutes without stopping.
2. Exceeding the shredding capacity, eg. inserting more than eight (8) sheets
of 20-lb. paper at one pass, or if the paper is not fed squarely into the
feed opening.
Both abnormal operations may result in the activation of the automatic motor overload
protection, which terminates the power to the unit. If this occurs you should:
1. Unplug the power cord from the AC outlet and wait at least 4 minutes
for the overload protection to reset. Tear or cut off any excess paper
from the top of the shredder.
2. Plug the power cord back into the AC outlet and place the Main Switch
in rev. Pull the remaining paper out of the cutters. Place the Main
Switch back to the auto position and if neccessary clear the feed opening
of any remaining shredded pieces of paper. Keep fingers away from
feed opening to avoid harm.
3. With the Main Switch in the auto position and the feed opening clear,
you are now ready to resume normal shredding.
Specifications:
Shred Type:
Cross-Cut
Shred Width:
5/32" X 1/8" or 4mm x 28mm
Shredding Capacity:
8 Sheets
Feed Opening:
8 3/4" or 222mm
Input:
115 volt AC, 2.5 amp.
3
ROYAL HT88 PAPER SHREDDER
Cautions:
1. Never allow children to shred or play with paper shredder or else serious
injury could occur.
2. Do not place hands or fingers into the shredder throat as serious injury
could result.
3. Never spray canned air or any type of spray lubricant into the shredder
while shredder is plugged in or serious injury could result.
4. Never place any lubricants or cleaning solutions into the paper shredder
or else serious injury could result.
5. Keep all loose articles of clothing, ties, jewelry, hair or other small items
away from the feed opening to prevent injury.
6. Remove all paper clips and staples from paper before shredding. The
shredder will cut staples and small paper clips; however, proper discretion
is recommended.
7. Keep the shredder turned off or unplugged when not in use for prolonged
periods of time.
8. When manually changing feed direction, pause long enough for the motor
to stop to avoid possible damage to the motor.
9. Always turn off and unplug the shredder prior to moving, cleaning or
emptying the wastebasket.
10.Empty the wastebasket frequently to avoid possible paper jams caused
by shredded material being pulled back into the cutter assembly.
Setup:
1. Place the shredder securely on top of the wastebasket. Be sure not
to allow your fingers to get between the basket and the shredder as
you are placing the shredder in place.
2. Plug the power cord into any standard 115-volt AC outlet.
3. Place the Main Switch in the auto position. The LED should illuminate. If the
LED does not light up, lift the shredder out of the wastebasket and place it back
in so that it sits flush inside of the wastebasket.
Operating the shredder:
The Main Switch is located on the top of the shredder. The Main Switch has four
(4) settings.
1. When auto is selected, the shredding process is started automatically
by inserting the paper into the feed opening. The shredder will stop
automatically when the paper has completed its travel through the feed
opening.
2. rev is used to assist in the removal of a paper jam, which reverses the
shredding process prior to a completed cycle, thus clearing the cutters.
3. off position is recommended when emptying the wastebasket or when
the shredder is not in use for a prolonged period of time.
4. fwd is used to assitst in clearing any excess paper from the cutters after the
completion of a shred cycle.
NOTE: The LED lights up in auto position only.
Shredder capacity:
HT88 will shred eight (8) sheets of 20-lb. bond paper and will accept paper widths up
to 8 3/4". When shredding small material like envelopes or credit card receipts, insert
them through the middle of the feed opening.
2
Содержание HT88
Страница 2: ...HT88 ...
