background image

16

 14.  WARRANTY

Royal  Sovereign  International  warrants  the  equipment  sold  is  free  from  defects  in 

material and workmanship for a period of One (1) year for Parts and Labor from the date 

of installation, excluding lamination rollers which are warranted for Six (6) months. This 

warranty  is  extended  only  to  the  original  purchaser. This  warranty  is  the  only  warranty 

made  by  Royal  Sovereign  International  and  cannot  be  modified  or  amended.  Royal 

Sovereign’s  sole  and  exclusive  liability  and  the  customer’s  sole  and  exclusive  remedy 

under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such 

defective  part  or  product. These  remedies  are  only  available  if  Royal  Sovereign’s 

examination of the product discloses to Royal Sovereign’s satisfaction that such defects 

actually  exist  and  were  not  caused  by  misuse,  neglect,  attempt  to  repair,  unauthorized 

alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.
All  warranty  claims  must  be  filed  through  the  authorized  Royal  Sovereign  dealer  or 

reseller through which the equipment was originally purchased. Model, serial number and 

date of delivery are required for all claims. 
The  warranty  made  herein  is  in  lieu  of  all  other  warranties,  expressed  or  implied, 

including  any  warranty  or  merchantability  or  fitness  for  a  particular  purpose.  Royal 

Sovereign  will  not  be  liable  for  personal  damage  or  personal  injury  (unless  primarily 

caused  by  its  negligence),  loss  of  profit,  or  other  incidental  or  consequential  damages 

arising out of the use or inability to use this equipment.      

This warranty specifically does not cover damage to laminating rollers caused by knives, 

razor  blades,  or  any  sharp  objects  or  abrasives,  or  failure  caused  by  adhesives,  or 

damage  caused  by  lifting,  tilting  or  improper  use  of  the  machine. Warranty  repair  or 

replacement  by  Royal  Sovereign  or  its  authorized  Reseller(s)  does  not  extend  the 

warranty  beyond  the  initial  one  year  period  from  the  date  of  installation.  Unauthorized 

customer alterations will void this warranty.         

LIMITED WARRANTY

RS International Australia PTY. LTD.

30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL  : +61) 2-9674-2127      
FAX  : +61) 2-9674-2027
E-mail : [email protected]

CORPORATE HEADQUARTERS

Royal Sovereign International Inc.

2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : +1) 800-397-1025        FAX : +1) 201-750-1022
E-mail : [email protected]

Royal Sovereign Inc. 

<Oversea Sales Office>

1001, World Meridian II, 426-5, Gasan-dong, 
Geumcheon-gu, Seoul, 153-759, KOREA
TEL  : +82)2-2025-8800     FAX  : +82)2-2025-8830
E-mail : [email protected]

RS Canada Inc.

1025 Westport Crescent, Mississauga On L5T 1E8  CANADA

TEL : +1) 905-461-1095  FAX : +1) 905-461-1096     

TF : +1) 866 961-6673

E-mail : [email protected]

RS Holland B.V.

Industrieweg 6K, 4104AR, Culemborg, The Netherlands

TEL :  +31 (0)345 473 097 

FAX :  +31 (0)345 519 811

E-mail : [email protected]

Содержание RSC-1050CL

















Отзывы: