background image

Troubleshooting

PROBLEM: The vehicle does not run

Possible Cause: 

The battery may be low on charge.

After each use, or once a month minimum, charge the battery for 8 to 12 hours. Do not leave 

the battery on the charger for more than 20 hours.

Possible Cause: 

Thermal fuse has tripped.

The vehicle is equipped with a self-resetting fuse. When the vehicle is overloaded or 
operated incorrectly; the self-resetting fuse will prevent use for 5 to 20s econds before 
becoming operational again. The self-resetting fuse is under the seat (Refer to the picture.)

To avoid tripping the fuse, follow these guidelines:

DO NOT overload the vehicle, Maximum weight = 30kg.

DO NOT tow anything behind the vehicle.

DO NOT drive up steep slopes.

DO NOT drive into fixed objects, which may cause

the wheels to spin, causing the motor to overheat.

DO NOT drive in very hot weather, components may

overheat.

DO NOT tamper with the electric system, Doing so may

create a short circuit, causing the fuse to trip.

Possible Cause: 

Wheel nuts are loose.

If the wheel nuts are not tight, the wheels will not engage the gears. Tighten the nut.

Possible Cause: 

Battery connector or wires are loose.

Make Sure the battery connectors are firmly plugged in to each other.

Possible Cause

Battery is no longer serviceable.

Have you properly maintained the battery according to directions? Is the battery old? 

The

 

battery may need to be replaced.

Possible Cause

Electric system is damaged.

Water may have corroded the system, or dirt

 etc may

 have jammed the switch.

Possible Cause

Motor is damaged.

The motor needs professional repair.

PROBLEM:

 

The

 

battery

 

will

 

not

 

recharge.

Possible Cause: 

Battery connector or adapter connector is loose. 

Make sure the battery connector and adapter connector are firmly plugged together.
Possible Cause: 

Charger is not plugged in.

Make sure the charger is plugged into the wall outlet and the power outlet is ON.

Possible Cause: 

Charger is not working.

Is the charger warm while charging? If not, the charger may be broken and may need to be 

replaced.

Содержание Ride-On Motorcycle


















Отзывы: