manualshive.com logo in svg

Roundup WD-50, Руководство пользователя, Страница: 6 / 16

Поделиться
Скачать
Roundup WD-50 Скачать руководство пользователя страница 6

WarMer DraWer

6

P/N 1011046 08/09

figure 1. wD-50

figure 2. wD-50 accessories

Unpacking

  1.  remove unit and all packing materials from the 

shipping carton.

  2.  Open the large box.  remove all packing materi-

als and protective coverings from the unit and 

parts.

  3.  Wash all removable parts in soap and water and 

wipe all surfaces of the unit with a hot damp 

cloth.

nOte:  Do nOt use a dripping wet cloth.  wring 

out before use.

  4.  reinstall all removed parts.  

nOte:  If any parts are missing or damaged,  

contact a.J. antunes & co. ImmeDIately at  

1-877-392-7854.

equipment setup

When placing the unit into service, pay attention to the 

following guidelines.

  •  Make sure power to the unit is off and the unit is 

at room temperature.

  •  Do NOT block or cover any openings on the unit.

  •  Do NOT immerse cord or plug in water.

  •  Keep cord away from heated surfaces.

  •  Do NOT allow cord to hang over edge of table or 

counter.

connect the unit to the power supply.  refer to the 

specification plate for the proper voltage.

InstallatIOn

Содержание WD-50

















Отзывы:

Нет отзывов