background image

WarMer DraWer

4

P/N 1011046 08/09

in addition to the warnings and cautions in this manual, 

use the following guidelines to safely operate this unit:

  •  Read all instructions before using equipment.

  •  For your safety, the equipment is furnished with 

a properly grounded cord connector.  Do NOt 

attempt to defeat the grounded connector.

  •  Install or locate the equipment only for its intend

-

ed use as described in this manual.  Do NOt use 

corrosive chemicals in this equipment.

  •  Do NOT operate this equipment if it has a dam

-

aged cord or plug, if it is not working properly, or 

if it has been damaged or dropped.

  •  This equipment should be serviced by qualified 

personnel only.  contact the nearest roundup 

authorized service agency for repair.

  •  Do NOT block or cover any openings on the unit.

  •  Do NOT immerse cord or plug in water.

  •  Keep cord away from heated surfaces.

  •  Do NOT allow cord to hang over edge of table or 

counter.

the following warnings and cautions appear throughout 

this manual and should be carefully observed:

  •  Turn the power off, unplug the power cord, and 

allow unit to cool down before performing any 

service or maintenance.

  •  The procedures in this chapter may include 

the use of chemical products.  these chemical 

products will be highlighted with bold face let-

ters followed by the abbreviated Hcs (Hazard 

communication standard).  see Hazard 

communication standard manual for the appro-

priated Material safety Data sheets (MsDs).

  •  The unit should be grounded according to local 

electrical codes to prevent the possibility of elec-

trical shock.  it requires a grounded receptacle 

with separate electrical lines, protected by fuses 

or circuit breaker of the proper rating.

  •  All electrical connections must be in accordance 

with local electrical codes and any other appli-

cable codes.

  • 

warnInG electrIcal shOcK hazarD.  

failure to follow these instructions could 

result in serious injury or death.

-  electrical ground is required on this appliance.
-  Do NOt modify the power supply cord plug.  

if it does not fit the outlet, have a proper outlet 

installed by a qualified electrician.

-  Do NOt use an extension cord with this unit.
-  check with a qualified electrician if you are 

unsure if the appliance is properly grounded.

warnInG

electrIcal shOcK hazarD.  failure to follow 

the instructions in this manual could result in 

serious injury or death.

•  Electrical ground is required on this appliance.

•  Do NOT modify the power supply cord plug.  If 

it does not fit the outlet, have a proper outlet 

installed by a qualified electrician.

•  Do NOT use an extension cord with this unit.

•  Check with a qualified electrician if you are 

unsure if the appliance is properly grounded.

ImpOrtant safety InfOrmatIOn

Содержание WD-50

















Отзывы: