ROUND Pools AMBASSADOR Скачать руководство пользователя страница 33

Страница: 33 / 40

No Diving or Jumping.

Observe all Safety Rules.

4-1

A. Attach your Verticals and Top Rails

1. Continue filling your Pool

a. Continue filling your pool with water. Do not put in more than 12" (30 cm) of water

until the top rails and vertical columns are all attached.

b. Keep working on the top rails and vertical columns while the pool fills.

• See the drawing on the next page for an overview of all the parts used to

install the verticals, top rails and top connectors.

2. Install the Vertical Columns

a. Line up the bottom of one vertical column (key

1) with the two small tabs on one base plate

(key 2). The tabs must be on the

inside

of the

vertical column. The three holes on the front of

the vertical must be nearest the top.

b. Line up the screw holes and fasten with one

self-tapping screw on each side (key 3).

c. Hook a top plate (key 4) over the top edge of the pool wall

(key 5). Place the top plate down over

the top of the vertical column with the tabs on

the

outside

of the column. Make sure the vertical column is

straight up and down.

d. Line up the screw holes and fasten with one self-tapping

screw on each side and one on the front (key 6).

e. Repeat the last four steps for each of the vertical columns

around the pool wall.

c. Prior to installing the connector, knock out

the holes shown in diagram 10.

ection

Pool Component Installation Manual

Installing the Top Ledges &

Uprights

Hint:

Use the ridges in the

pool wall to make sure

the vertical column is

straight up and down.

B A

Содержание AMBASSADOR









































Результаты поиска

Содержание AMBASSADOR

Отзывы:

Похожие инструкции для AMBASSADOR

Бренды по названию

Популярные бренды

ROUND Pools AMBASSADOR, Руководство по установке

Результаты поиска

Содержание AMBASSADOR

Отзывы:

Похожие инструкции для AMBASSADOR

Бренды по названию

Популярные бренды