manualshive.com logo in svg

RotorSport Bishops Castle, Руководство по обслуживанию

Поделиться
Скачать
RotorSport Bishops Castle Скачать руководство пользователя страница 55

Copyright of RotorSport UK Ltd

Document number RSUK0288

Page 55 of 55

25-60-00 0-1 DESCRIPTION: EMERGENCY LOCATOR TRANSMITTER (p1)
UK-registered aircraft are not fitted with an ELT

26-00-00 0-1 DESCRIPTION: FIRE INDICATING SYSTEM (p1)
Although functionally the same as the system described in the AutoGyro MMM, the 
system fitted to UK-registered aircraft has the detector wire extended into the protected 
compartment between the cockpit bulkhead and the removable fire-resistant panel.

34-10-00 5-1 TEST: PITOT STATIC SYSTEM INTEGRITY (p1)
The procedure for field testing the pitot-static system of UK-registered aircraft is described 
on p20 above

61-10-00 4-1 REMOVAL-INSTALLATION: PROPELLER – HTC (p1), ADJUSTMENT (p1) 
and REPAIR (p1)
Information for UK-registered aircraft is provided at p24 above

62-11-00 4-2 DISASSEMBLY: ROTOR - TEETERING PARTS (p1) and ASSEMBLY (p1)
UK-registered aircraft utilise low-profile “Binx” all-metal locking nuts in place of nyloc nuts 
for retention of the teeter-block to the hub-bars assembly (4-plcs).  These Binx nuts should 
be tightened to 20Nm.  The remaining orthodox nyloc nuts should be tightened to 25Nm.
UK-registered aircraft use a reduced angle-of-incidence variant of RotorSystem II (part 
number BG4836 under BOM location V.RK303).  The assembly is the same in concept 
but may be recognised by the black-coloured clamping profile replacing the silver coloured 
item of the standard assembly.

62-32-00 6-1 INSPECTION: ROTOR GIMBAL HEAD (p1)
UK-registered aircraft have additional large-diameter thrust washers RSD1121 fitted to the 
roll axis of the gimbal head. Other than ensuring that these are properly located around 
the head of the flanged bushes fitted into the gimbal block there is no difference to 
assembly technique.

          

      

                  Pitch/roll block and slotted washer                                   Slotted washer in place

Page issue 3, dated 12.04.13

Содержание Bishops Castle
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды