Rotomec CYCLONE C50 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 44

Rotomec CYCLONE C50 Series Скачать руководство пользователя страница 29

In the collapsed position the driveline should be approximately 5 cm. (2") from bottom-
ing out to prevent possible damage to the tractor or implement. When the PTO is in the
maximum extended position, the ideal minimum overlap of the two halves should be
approximately 15 cm. (6")

(see fig. 15)

.

If determined that the driveline is too long, follow these procedures to adjust the length:

1. separate the two driveline halves. Connect one half to the tractor PTO and the

other half to the mower.

2. Raise and lower the mower with the 3 point hitch to find the position where the

driveline is shortest. Hold the half shafts side by side and mark the desired length
on the outer female tube guard leaving a 5 cm. (2") gap between the end of the
guard tube and bell guard.

3. Cut off both guard tubes the same amount as marked in step 2.
4. Shorten both drive tubes the same amount as guard tubes.
5. De-burr and clean filings from drive tubes and apply grease to outside of inner

telescoping tube.

Reassemble the driveline halves and connect to tractor and mower. Raise and lower
mower again to be sure driveline does not bottom out in its shortest position and has a
minimum overlap of 15 cm. (6") in the longest position.

CAUTION: always work with the driveline as straight as possible. This will
prolong its life and that of its components. It is advised, not to work at an angle
greater than 15 degrees.
When the mower is not hooked to the tractor, the driveline must be

supported by

the storage hook attached to the top link.

4.07 - Transport

Before  raising  the  mower  for  transport,  the  tractor  top  link  must  be  adjusted  so  when
lifted,  the  rear  of  the  machine  is  higher  than  the  front  (the  mower's  nose  is  tilted
downward).  To  do  this,  shorten  the  tractor  top  link  until  the  top  hitch  plate  is  locked
forward  and  no  longer  able  to  pivot.  This  will  keep  the  mower  locked  in  position  and
minimize  the  shaking  and  bouncing  during  transport  which  can  damage  the  hitch  or
frame.
When raising the mower be sure the PTO driveline does not hit either the mower or the
tractor.  During  transport  the  mower should  not  be  lifted  over  35-40  cm.  (14"-16")  from
the ground.

CYCLONE 'C50'

OPERATOR'S MANUAL

SAFETY PRECAUTIONS

29

ROTOMEC

«
...
27
28
29
30
31
...
»

Содержание CYCLONE C50 Series













































Отзывы:

Нет отзывов