95
User manual
Room air conditioner - MIRAI X
EN
8.4. Timing set
TIMER button is for set TIME ON /TIME OFF these two types of timing.
Timing ON time and CLOCK are display at the same displayed zone. When the Timing ON has been set, the
CLOCK displayed zone would show the Timing ON information. Press the CLOCK key to query the current time,
which would last for 3 seconds and then recover to Timing ON information.
During the setting the timing, press the CANCEL button to exit the timing set.
For the first time press the TIMER button, the icon of “TIME ON” will display and the timing time will flashing
at the 1Hz, while the “TIMER OFF” icon will not show and the timing off time would not flash (in the case of
without timing off setting, the information will not show). Press the TIMING key again, the “TIME OFF” icon will
show and the timing time will flashing at 1Hz; while the “TIME ON” icon will not show and the timing on time
would not flash (in the case of without timing on setting, the information will not show). Button pressing base
on this circulating logic.
8.4.1. Set the Timing ON time only
In case originally provide with timing set in the system, please press the CANCEL button to cancel the
current settings.
1. Press the TIMER button, the LCD in the wire controller will show “TIME ON”, at the same time the
time zone will display the last setting time, which flash at the frequency of 1Hz, the wire control
enters to Timing ON status.
2. By using and to set the desired Timing ON time.
3. After 0.5 seconds of done the setting, the wire controller will deliver the Timing ON information,
2 seconds later, the Timing ON information will stop flashing. Timing ON has been set.
8.4.2. Set Timing ON and OFF
In case originally provide with timing set in the system, please press the CANCEL button to cancel the
current settings.
1. Press the TIMER button, the LCD in the wire controller will show “TIME ON”, at the same time the
time zone will display the last setting time, which flash at the frequency of 1Hz, the wire control
enters to Timing ON status.
2. By using and to set the desired Timing ON time.
3. Press the TIMER button again, the LCD in the wire controller will show “TIME OFF”, at the same time
the time zone will display the last setting time, which flash at the frequency of 1Hz, the wire control
enters to Timing OFF status.
4. By using and to set the desired Timing OFF time.
5. After 0.5 seconds of done the setting, the wire controller will deliver the Timing OFF information,
2 seconds later, the Timing OFF information will stop flashing. Timing OFF has been set.
8.4.3. Modify the timing settings
For modify the TIMING OFF/TIMING ON, please press the corresponding timing button to reset it.
Note:
The set time is the relative time that is relative to the standard time when setting the wire controller, which
would delay for a while.
PART 6. ZATO WIRED CONTROLLER SUPPORT
Содержание M35X
