Rotem RLD 7.2 Скачать руководство пользователя страница 7

 

7  

RLD 

|

 3.0/4.01 

3  INTRODUCTION TO THE RLD-7.2 AND RLD-14 

The RLD-7.2 and RLD-14 units enable controlling the light and brightness in the poultry pen.  The Rotem 
Platinum, AC-2000 and SuperGuard Controllers support the RLD.  This manual is meant to be used by 
either a poultry farmer or authorized personnel who own a poultry pen.  

 

Device Description 

 

Software Type 

 

Abbreviations and Terms 

 

User Interface 

3.1  Device Description 

The RLD-7.2 and RLD-14 are two independent channel devices controlling all light functions inside the 
poultry house.  These dimmers have unique features such as stable operation in low brightness levels and 
high flexibility. 

  

Main features

 

Two independent channels  

 

Manual brightness control 

 

Programmable brightness control by analog signal 0 - 10 VDC and communication line from the 
controller 

 

*Automatic settings recovery after power failure 

 

Automatic settings save for each mode. 

 

Minimum and maximum light intensity settings 

 

Automatic shut down timer. 

 

Maximal output power for one channel  

o

  230 VAC, 7200 VA (RLD-14) 

o

  110 VAC, 3600 VA  (RLD-7.2) 

NOTE: 

*The settings are immediately saved after being defined

 

3.2  Software Type 

Rotem currently supports two software versions: 

 

Version 3.0 supports: 

o

  CPU card version 1.3.1 (refer to Figure 6) 

 

Version 4.01 supports: 

o

  CPU card version 2.0 (refer to Figure 5) 

Содержание RLD 7.2























Отзывы: