42
RSP-1580 SURROUND SOUND PROCESSOR
EQ VALUE:
This menu allows you to enter the EQ value. There are total
10 bands as below.
E Q V A L U E S E T
S P E A K E R A L L S P E A K E R
- - - - - - - - 1 - - - - 2 - - - - 3 - - - - - 4 - - - - - 5 -
F r e q :
4 0
6 0
1 0 0
1 2 0
1 6 0
Q
:
2
2
2
2
2
G a i n :
0
0
0
0
0
- - - - - - - - 6 - - - - 7 - - - - 8 - - - - - 9 - - - - 1 0 -
F r e q : 1 3 0 0
1 7 5 0
4 K
1 0 K
1 6 K
Q
:
2
2
2
2
2
G a i n :
0
0
0
0
0
E Q S E T U P M E N U
:
BAND 1 Freq : 20Hz - 80Hz, 1Hz Step
BAND 2 Freq: 20Hz - 80Hz, 1Hz Step
BAND 3 Freq: 81Hz - 140Hz, 1Hz Step
BAND 4 Freq: 81Hz - 140Hz, 1Hz Step
BAND 5 Freq: 141Hz - 200Hz, 1Hz Step
BAND 6 Freq: 1110Hz - 1550 Hz, 10Hz Step
BAND 7 Freq: 1560Hz - 2000 Hz, 10Hz Step
BAND 8 Freq: 2.1kHz - 8kHz, 100Hz Step
BAND 9 Freq: 8.1kHz - 14kHz, 100Hz Step
BAND 10 Freq: 14.1kHz - 20kHz, 100Hz Step
Q : 1 - 24
Gain : -12dB - 0 - +12dB
Note:
Q in EQ value relates to the bandwidth of the filter. The higher
the value, the narrower the bandwidth.
Troubleshooting
Most difficulties in audio systems are the result of incorrect connections,
or improper control settings. If you encounter problems, isolate the area
of the difficulty, check the control settings, determine the cause of the fault
and make the necessary changes. If you are unable to get sound from
the unit, refer to the suggestions for the following conditions:
The unit does not turn on
Make sure the power cord is plugged into the rear panel and a
•
AC outlet.
Make sure the rear panel POWER switch is in the ON position.
•
No sound from any input
Make sure that MUTING is off and VOLUME is turned up.
•
Make sure that preamp outputs are connected to a power amplifier
•
and that the amplifier is turned on.
Make sure source inputs are connected and configured correctly.
•
Check that the setting for HDMI AUDIO in the VIDEO/HDMI on-
•
screen menu is AMP MODE.
No sound from digital sources
Make sure that digital input connector is assigned to the proper
•
source input and that the source input is configured to use the digital
nput rather than an analog input.
Check the configuration of the DVD player to ensure that the bitstream
•
and/or DTS digital output is activated.s.
No sound from some speakers
Check all power amp and speaker connections.
•
Check Speaker Configuration settings in the Setup menus.
•
No video output on TV monitor .
Make sure that the TV monitor is connected properly and check the
•
input assignments. S-Video and Composite Video TV monitors can
only be used with interlaced SD sources. HDMI and Component
TV monitors can be used with Standard Definition (SD) and High
Definition (HD) sources. An HDMI 1080p source can only be sent
to a 1080p-compliant TV monitor .
Component Video output at 720p or 1080i may not be available
•
if the source signal includes HDCP copy protection.
HDMI cables must be 5 meters or less in length.
•
In MON 2 - 4 if watching the same source as MAIN room, make
•
sure the video output is compatible with the MON 2 - 4 monitor.
The priority will be given to the MAIN room.
If watching 3D source, make sure the display is 3D enabled.
•
OSD menus are not displayed on TV Monitor
Make sure the unit is not in HDMI Bypass mode or that a 3D movie
•
is playing. In either case the OSD is only available on the front
panel LCD.
