39
English
meters) in 0.5 foot (0.15m) increments with each increment equivalent
to an additional delay of 0.5ms.
To change a setting, place the highlight on the desired line using the
Up/Down buttons and use the Left/Right buttons to increase or decrease
the delay. To return to the MAIN menu, press the ENTER button. Press
the MENU/OSD button on the remote to cancel the display and return
to normal operation.
Miscellaneous Settings
Other Opinion
O T H E R
O P T I O N S
R E C O R D : S o u r c e
T U R N O N V O L : L a s t
M A X V O L : M a x
P O W E R : D i r e c t
L A N G U A G E : E N G L I S H
D I S C R E T E : N o
S / W U P G R A D E : E n t e r
M A I N
M E N U
This OTHER OPTIONS menu, accessed from the MAIN menu, provides
access to several miscellaneous settings as follows:
RECORD:
Select which source signal to be sent to the recording outputs
by choosing one of the input sources. The options are: CD, TAPE, TUNER,
VIDEO 1–5, and SOURCE. You can either select a specific component
or select SOURCE which will send the signal to the record outputs from
whatever source is selected for listening. The default is SOURCE.
TURN ON VOL:
Specifies a default volume level to be used each time
the unit is activated. You can select LAST to have the unit power up with
the last previously used volume setting. Or, you specify a volume from
MIN (full mute) to MAX, in 1dB increments. Note that this setting cannot
exceed the MAX VOL established in the next line of the menu.
MAX VOL:
Specifies the maximum volume level for the unit. The volume
cannot be adjusted above this level. Settings range from MIN to MAX,
in 1dB increments.
POWER:
This setting determines how the unit powers up.With the default
STANDBY setting, the unit powers up in standby mode when AC is applied
and the rear panel POWER button is ON. The unit must be activated using
the front panel STANDBY button or the remote ON/OFF buttons.
With the DIRECT setting, the unit is fully activated when AC power is
applied and the rear panel POWER button is ON; however, it may be
put in standby mode using the front panel STANDBY button or the remote
ON/OFF buttons.
In ALWAYS-ON mode, the unit remains fully active whenever AC is present
and the rear panel POWER button is ON; the front panel STANDBY button
and the remote ON/OFF buttons are disabled and the unit cannot be
put in standby mode.
In RESUME mode, the unit will return to the last power condition setting
when switched on. For example, when the AC mains power is switched
OFF during operation, it will return to operating mode when the mains
power is switched on again.
LANGUAGE:
Selects a language for the On Screen Display
DISCRETE:
The default setting of NO allows control of input selection in
remote monitors MON 2–4 from the main room remote control. Changing
the setting to YES prevents the remote control in the main room from
affecting any remote monitors in any way.
The discrete option does not affect the control of the MON from the front
panel buttons in any way.
Note:
The DISCRETE function is intended for use by a Rotel dealer or
installer only.
Rotel’s use of discrete IR commands in multi-zone models provides easier
integration with IR control systems, making control possible from a single
IR input. For Rotel dealers or installers, further information is available on
the Rotel website: www.rotel.com
Go to ‘Support’ for downloads and technical updates, or seach for
‘discrete’ to find relevant items. Remote commands are available in Philips
Pronto CCF format and in RTI CML format at:
www.rotel.com/downloads/prontocodes.htm
www.rotel.com/downloads/rticodes.htm
S/W UPGRADE :
Enter this menu if you wish to upgrade the LCD and
Scaler firmware.
Note:
The S/W UPGRADE function is intended for use by a Rotel dealer
or installer only.
Change settings on the OTHER OPTIONS menu by highlighting the desired
line using the Up/Down buttons and using the Left/Right buttons to step
through the available settings. To return to the MAIN menu, press the
ENTER button. Press the MENU/OSD button on the remote to cancel the
display and return to normal operation.
Video/HDMI SETUP
V I D E O / H D M I
V I D
O U T
F O R M A T : 4 8 0 p / 5 7 6 p
H D M I
A U D I O
M O D E : A M P
M o d e
H D M I
B Y P A S S : N o
M A I N
M E N U
The VIDEO/HDMI menu deals with the configuration of the HDMI and
Component output for high-definition video display devices. See the Video
Inputs & Outputs section of this manual.
VIDEO OUT FORMAT:
Specifies the video resolution and format of the
video output at the TV MONITOR outputs. The processor will scale all
video inputs up to this specified resolution for a perfect match with the
native resolution of your HDTV monitor . Can be 480p/576p, 720p,
1080i, 1080p.
