11
English
NOTE: You must insert the Wi-Fi dongle (or wire adaptor) to the
ETHERNET port on the rear panel. The unit will first search for available
networks before allowing access to DAB and FM functions. If networks
are not available, the unit will display “Network Error”. FM and DAB
functions will operate normally after the initial network search.
ANALOG INPUT-AUX 2
D
The RCX-1500 can receive analog music signals from other sources, such
as your CD players analog outputs. Connect the LEFT and RIGHT outputs
of the source to the LEFT and RIGHT input of the AUX 2 Input.
PRE OUT
E
The RCX-1500 can send analog signals to a second amplifier through
the connectors labeled PRE OUT. Use this connection if you wish to use
another power amplifier to drive your speakers.
Network Connection
F
Connect the Rotel supplied USB Wi-Fi dongle to the USB port on the RCX-
1500 rear panel labeled ETHERNET. The RCX-1500 has been configured
to work with the supplied USB Wi-Fi dongle. No additional software/
setup is required. The RCX-1500 is now ready to connect to your wireless
LAN. Refer to Internet Radio section for detailed setup.
NOTE: Not all USB Wi-Fi/Wired dongles will operate with the RCX-1500.
Please use the one supplied by Rotel.
DIGITAL INPUT-AUX 1
G
The RCX-1500 can play digital music signal from other sources, such as
your CD player’s digital output. There are two connectors on the AUX
1 Digital Input area on the rear panel, labeled with coaxial and optical.
Connect the coaxial or optical output of your source to the coaxial or
optical input of the RCX-1500.
Computer I/O
H
This RCX-1500 can be operated from a computer with audio system
control software from third-party developers. This control is accomplished
by sending operating codes from the computer via a hard-wired RS-232
serial connection. In addition, RCX-1500 can be updated using special
software from Rotel.
For additional information on the connections, cabling, software, and
operating codes for computer control or updating of the unit, contact
your authorized Rotel dealer.
Speaker Connections
I
Speaker Selection
The nominal impedance of the loudspeakers connected to each channel
of the RCX-1500 should be no lower than 4 ohms.
Speaker Wire Selection
Use insulated two-conductor stranded wire to connect the unit to the
speakers. The size and quality of the wire can have an audible effect
on the performance of the system. Standard speaker wire will work,
but can result in lower output or diminished bass response, particularly
over longer distances. In general, heavier wire will improve the sound.
For best performance, you may want to consider special high-quality
speaker cables. Your authorized Rotel dealer can help in selection of
appropriate cables for your system.
AC Power and Control
AC Power Input
J
Your RCX-1500 is configured at the factory for the proper AC line voltage
in the country where you purchased it (USA: 120 volts/60 Hz, Europe:
230 volts/50 Hz). The AC line configuration is noted on a label on the
back panel.
The RCX-1500 is supplied with the proper AC power cord. Use only this
cord or an exact equivalent. Do not modify the supplied cord. Do not
use an extension cord.
Be sure the power switch on the front panel of the RCX-1500 is turned
off. Then, plug one end of the cord into the AC power connector on
the back panel of the amplifier. Plug the other end into an appropriate
AC outlet.
If you are going to be away from home for an extended period of time,
it is a sensible precaution to unplug your receiver.
Standby Switch and Indicator Light
1
2
The Standby Switch is located on the left side of the front panel. The
Standby Indicator ring will illuminate when the AC mains are connected.
This indicates the unit is in Standby mode.
To turn the unit ON, push the Standby switch once, the front display
will illuminate, indicating the unit is out of Standby mode and ready
for operation.
Connection Overview
Before continuing further to other sections in the manual, please make
sure all the cable connections are made properly. Refer to figure 2.
USB Connection
A
The socket on the front panel below the STANDBY switch is for USB
connection. Music storage devices can be accessed by the RCX-1500
through this input. Music storage devices such as MP3 players, iPod, USB
memory sticks or any other form of memory devices with USB interface
can be connected to the RCX-1500 through the front USB socket. RCX-
1500 will automatically search music files from the connected storage
device.
NOTE: RCX-1500 use USB 2.0 standard to access music files. The unit
can playback music files stored on storage devices that are compliant
with USB 2.0 standard. However, it will not operate with devices that
require additional drivers.
PHONES Connection
B
The socket on the front panel below the USB socket is for headphones.
Plug a 3.5mm headphone jack into the socket to listen to music through
headphones. Connecting headphones will automatically turn off the
output to the loudspeakers.
DAB/FM Broadcasting
C
Please use supplied indoor antenna to connect the DAB and FM connector
on the rear panel. To receive the best FM signal, make sure there is enough
room for the T-shaped indoor antenna to fully extend. Eyelets at both
ends of the T allow tacking the antenna to a wall if desired. Experiment
with different positions to maximize reception.
