Ross NK-3G144 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 64

Ross NK-3G144 Скачать руководство пользователя страница 26

26 • Installation

NK-3G144 User Guide (v04)

7. Screw the PSU to the frame using the two captive screws in the PSU. The two captive screws should always be

fastened to prevent movement of the PSUs in the frame.

8. Switch the PSU on by using the switch on the front of the PSU.

9. Close the front door.

10. Insert and tighten the front door screw to secure the front door of the NK-3G144 shut.

For More Information on...

• replacing the PSU, see “

Replacing a PSU in the NK-3G144

” on page 55.

Installing the Routing Switcher System in a Daisy-Chain Layout

You may connect NK Series equipment in a daisy-chain layout. The items are connected via the T-Bus control
system. However, if the T-Bus chain is broken, for example, by accidentally disconnecting a cable, downstream
devices are also disconnected. T-Bus RJ-45 sockets on devices downstream from the NK-IPS are passively
connected internally, so device failure or power disconnection does not disrupt communication with other devices
in the chain.

Each T-Bus connector on the NK-IPS has an independent driver/receiver ensuring that each of the eight T-Bus
connectors will not be affected by a device failure on any other connector.

Figure 4.3 NK Series equipment in a daisy-chain layout

To connect the NK Series equipment in a daisy-chain layout

1. Install the equipment into the rack frame, then fix in place with appropriate fasteners.

2. Connect the NK-3G144 directly to the AC mains via the IEC connectors on the rear panel.

NK-IPS

Network Bridge

ETHERNET

POWER

Service
Port

T-BUS

RCP-NKQ

Remote Control Panel

PSU

T-BUS

NK-3G144

Digital Video Routing Switcher

VID REF

T-BUS

Appropriate

NK Series

Power Supply

NK Series

5V, 2A

Power Supply

AC Mains

AC Mains

«
...
24
25
26
27
28
...
»

Содержание NK-3G144

































































Отзывы:

Нет отзывов