Ross NK-3G144 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 64

Ross NK-3G144 Скачать руководство пользователя страница 11

RCP Series User Guide (v04)

Before You Begin • 11

Before You Begin

The NK-3G144 Routing Switcher handles high-bandwidth, broadcast-quality, digital video and audio signals, and
embedded audio signals. Digital video signals can be 3G, high definition, standard definition, DVB-ASI, or SDTI.
The NK-3G144 supports SMPTE standards 424M, 344M, 259M, and 292M and AES.

Features

The NK-3G144 Routing Switcher provides the following features:

• economical and professional-quality design
• a powerful control system
• support for 3G and multi-definition digital video and AES digital audio
• 10 RU design with slots for duplicate output cards
• control, switching matrix, and power redundancy options
• hot swapping of all boards and power supplies
• smart fan control and monitoring
• enhanced LED indications via the Heartbeat, cards, and power supply
• extensive monitoring via DashBoard
• firmware is fully upgradeable using DashBoard
• fully upgradeable for Carbonite eXtreme (if you have the 2500AR-202-

XX

frame)

Typical System Equipment

Routing switchers may be connected to other NK Series devices via the T-Bus control system to form a multi-level
routing switcher system. For smaller routing applications, routing switchers may be used individually to provide
switching across a single router level or signal type. The NK Series of routing switchers may be controlled by:

• an NK Series remote control panel
• the DashBoard NK Switchboard
• an automation system or RS232 terminal, via an NK-SCP/A ASCII/RS232 Control Interface
• the NK-VCP Virtual Control Panel
• the NK-GPI General Purpose Interface

DashBoard software may be used to set up each routing switcher via an NK-IPS Network Bridge. These parameters
can be saved in a configuration file and sent to a routing switcher at any time using DashBoard.

Typical equipment that is used in an NK Series routing switcher system includes:

• any of the NK Series routing switchers with its appropriate power supply
• an NK-IPS Network Bridge
• an RCP-NK1, RCP-NKM, or RCP-NKQ Remote Control Panel
• a PC running DashBoard, connected via a CAT5 Ethernet cable to the NK-IPS
• standard source and destination equipment (for example, cameras, VTRs, servers)



If you are connecting the PC directly to the NK-IPS, use a crossover CAT5 Ethernet cable.



If you are connecting the PC indirectly via an Ethernet switch to the NK-IPS, use a straight-through CAT5
Ethernet cable.

«
...
9
10
11
12
13
...
»

Содержание NK-3G144

































































Отзывы:

Нет отзывов