background image

Output Mute Jumper 

Select one of the following options on 

JP1

 as follows, to enable or disable the Output Mute option:  

• 

Low Sig

 —  output will be muted if the input signal degrades to the point that the 

input EQ can no longer guarantee error-free performance.  When the red ERROR 
LED is on, the outputs will be muted. 

• 

Off

 —  the card will work to the limits of the input stage (default setting). 

Fault Report (SMPTE 269M) Jumper 

Select SMPTE 269M Fault Reporting, 

EN

ABLED or 

DIS

ABLED, via 

JP5

. The default is 

EN

See Chapter 3, “

SMPTE 269M Fault Reporting

” for complete details. 

Equalization Setting 

Use figure 2, the card labeling, and the following discussion to adjust the CMA-8011A equalization 
setting.  

Set the analog output EQUALIZATION adjustment (RV2) for the cable length used between the 
amplifier and analog destination equipment.  Plug the board into the frame and apply power.  

The equalization control is calibrated for Belden 8281 cable.  For other types of cable, put the board 
on the extender, apply a D1 color bar signal and, using a scope, set the EQUALIZATION adjustment 
for correct chroma level at the destination. 

Board Installation 

Use the following steps to install the CMA-8011A cards in a RossGear DFR-8104A or DFR-8110A 
digital frame: 

1.  Refer to the User Manual of the RossGear frame to ensure that the frame is properly 

installed according to instructions. If this module is to be installed in any compatible 
frame other than a Ross Video product, refer to the frame manufacturer’s manual for 
specific instructions.  

2.  Please note that heat and power distribution requirements within a frame may dictate 

specific slot placement of cards.  Cards with many heat-producing components 
should be arranged to avoid areas of excess heat build-up, particularly in frames 
using convectional cooling. 

3.  After selecting the desired frame installation slot, hold the CMA-8011A card by the 

edges and carefully align the card edges with the slots in the frame. Then fully insert 
the card into the frame until the rear connection plug is properly seated. 

BNC Labels 

Affix the supplied BNC label, as per the included instructions, to the BNC area on the rear of the rack 
frame. 

CMA-8011A User Manual (Iss.05) 

Installation and Setup  

  2-3 

Содержание CMA-8011A





























Отзывы: