manualshive.com logo in svg

Rosemount 8712E, Быстрая установка

Поделиться
Скачать
Rosemount 8712E Скачать руководство пользователя страница 17

4.2.1

Installation

1. Insert studs for the the bottom side of the sensor between the pipe

flanges and center the alignment spacer in the middle of the stud. See 

Figure 4-3

 for the bolt hole locations recommended for the spacers

provided. Stud specifications are listed in 

Table 4-6

.

2. Place the sensor between the flanges. Make sure the alignment spacers

are properly centered on the studs. For vertical flow installations slide the
o-ring over the stud to keep the spacer in place. See 

Figure 4-3

. Ensure the

spacers match the flange size and class rating for the process flanges. See 

Table 4-5

.

3. Insert the remaining studs, washers, and nuts.
4. Tighten to the torque specifications shown in 

Table 4-7

. Do not over-

tighten the bolts or the liner may be damaged.

Rosemount 8711 torque specifications

Table 4-7:   

Size code

Line size

Pound-feet

Newton-meter

015

1.5-in. (40 mm)

15

20

020

2-in. (50 mm)

25

34

030

3-in. (80 mm)

40

54

040

4-in. (100 mm)

30

41

060

6-in. (150 mm)

50

68

080

8-in. (200 mm)

70

95

4.3

Sanitary senors

Gaskets

The sensor requires a gasket at each of its connections to adjacent devices or
piping. The gasket material selected must be compatible with the process
fluid and operating conditions.

Note

Gaskets are supplied between the IDF fitting and the process connection
fitting, such as a Tri-Clamp fitting, on all Rosemount 8721 Sanitary sensors
except when the process connection fittings are not supplied and the only
connection type is an IDF fitting.

Alignment and bolting

Standard plant practices should be followed when installing a magmeter with
sanitary fittings. Unique torque values and bolting techniques are not
required.

November 2017

Quick Install Guide

Quick Install Guide 

17

Содержание 8712E





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды