Rosemount 485 Annubar Скачать руководство пользователя страница 6

Страница: 6 / 16

Quick Installation Guide

00825-0100-4809, Rev DB

December 2009

Flanged 485 Annubar

TEP

CONTINUED

...

Horizontal Orientation

For proper venting and draining, the sensor should be located in the upper half of the pipe

for air and gas applications. For liquid and steam applications, the sensor should be located

in the bottom half of the pipe. The maximum temperature for a direct mounted transmitter is

500 °F (260 °C).

NOTE:

For steam applications with DP readings between 0.75 and 2 inH

O in horizontal pipes, it is

recommended to install the primary element / flowmeter mounting above the pipe.

Figure 2. Gas

Figure 3. Liquid and Steam

Figure 4. Top Mounting for Steam (direct mount up

to 400 °F (205 °C))

45°

Recommended
Zone 90°

30°

Recommended
Zone 30°

Recommended

Zone 30°

45°

30°

Recommended
Zone 30°

Recommended

Zone 30°

45°

0100-4809 Rev DB.fm Page 6 Wednesday, December 30, 2009 3:57 PM

Содержание 485 Annubar

















Результаты поиска

Содержание 485 Annubar

Отзывы:

Похожие инструкции для 485 Annubar

Бренды по названию

Популярные бренды

Rosemount 485 Annubar, Быстрое руководство по установке

Результаты поиска

Содержание 485 Annubar

Отзывы:

Похожие инструкции для 485 Annubar

Бренды по названию

Популярные бренды