Rosemount 333 HART Tri-Loop Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 48

background image

HART Tri-Loop HART-to-Analog Signal Converter

B-4

CONNECTIONS AND
HARDWARE

The HART Communicator Model 275 can interface with a transmitter
from the control room, the instrument site, or any wiring termination
point in the loop through the rear connection panel as shown in Figure
B-2. To communicate, connect the HART Communicator in parallel
with the instrument or load resistor. The connections are non-polarized.

FIGURE B-2. Rear Connection Panel
with Optional NiCad Recharger Pack.

NOTE

The HART Communicator needs a minimum of 250 ohms resistance in
the loop to function properly. The HART Communicator does not
measure loop current directly.

Explosions can result in death or serious injury. Do not
make connections to the serial port or NiCad recharger jack
in an explosive atmosphere.

Explosions can result in death or serious injury. Before
connecting the HART Communicator in an explosive
atmosphere, make sure the instruments in the loop are
installed in accordance with intrinsically safe or
nonincendive field wiring practices.

Loop Connection Ports

Serial Port

Optional NiCad

Recharger Jack

2

75-

008

A

B

«
...
36
37
38
39
40
...
»

Содержание 333 HART Tri-Loop

















































Отзывы:

Нет отзывов

Похожие инструкции для 333 HART Tri-Loop

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 29

Бренд: NEC Страницы: 2

Бренд: XS Scuba Страницы: 4

Бренд: OST Страницы: 2

Steca coolcept 3 fleX

Бренд: KATEK Страницы: 40

Бренд: Jensen Страницы: 18

GUARDIAN SERIES

Бренд: Generac Power Systems Страницы: 12

Бренд: V-TAC Страницы: 54

Бренд: Pyramid Страницы: 39

Бренд: Volt Polska Страницы: 5

FRN0001C2S-2A FRN0002C2S-2A FRN0004C2S-2A FRN0006C2S-2A FRN0010C2S-2A FRN0012C2S-2A FRN0020C2S-2A FRN0025C2S-2A FRN0033C2S-2A FR

Бренд: Fuji Electric Страницы: 263

Бренд: TRUlink Страницы: 15

Бренд: Tektronix Страницы: 2

Бренд: RDZ Страницы: 60

AVerCaster Combo

Бренд: Avermedia Страницы: 2

Бренд: ZeeVee Страницы: 8

Бренд: Lindy Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды