Rosemount 333 HART Tri-Loop Скачать руководство пользователя страница 28

Страница: 28 / 48

HART Tri-Loop HART-to-Analog Signal Converter

5-2

Load Limitations

Loop resistance is determined by the voltage level of the external power
supply, as described by:

Temperature Limits

Ambient

50 to 104 °F (10 to 40 °C).

Storage

–40 to 158 °F (–40 to 70 °C).

Humidity Limits

0–95% non-condensing relative humidity.

Failure Mode Alarm

If Tri-Loop diagnostics detect a transmitter malfunction or a Tri-Loop
failure, the analog signal will be driven either below 3.75 mA or above
21.75 mA to alert the user. The high or low alarm signal is selectable by
the Tri-Loop Model Number.

Performance
Specifications

NOTE

The performance specifications below are for the HART Tri-Loop only.

Reference Accuracy

±0.045% of span.

Ambient Temperature Effect per 50 °F (28 °C)

±0.15% of span.

Stability

±0.1% of span for 12 months.

Analog Output Update

Tri-Loop responds to every HART burst update.
(Typical transmitter burst update rate: 0.3 to 0.5 s.)

Tri-Loop Response Time (after each burst update)

Channel 1–120 ms; Channel 2–220 ms; Channel 3–320 ms.

Total Response Time

Typical response time from sensor change to transmitter to Tri-Loop
analog update: 0.7 to 1.0 s.

Physical Specifications

Electrical Connections

Screw clamps. Accepts 24-12 AWG solid or stranded wire.

Dimensions

1.57

3.11

3.36 in. (40

85,5 mm)

DIN Rail Mounting Options

Asymmetrical 32mm G rail, symmetrical 35

7.5 mm top hat rail, or

symmetrical 35

15 mm top hat rail.

Weight

0.27 lb (0,12 kg)

1427
1200
1000

800
600
400
200

42.4

(Oh

Max. Loop Resistance = Power Supply Voltage–11.0

0.022

Power Supply Voltage, V dc

Operating Region

Содержание 333 HART Tri-Loop

















































Результаты поиска

Содержание 333 HART Tri-Loop

Отзывы:

Похожие инструкции для 333 HART Tri-Loop

Бренды по названию

Популярные бренды

Rosemount 333 HART Tri-Loop, Руководство по эксплуатации продукта

Результаты поиска

Содержание 333 HART Tri-Loop

Отзывы:

Похожие инструкции для 333 HART Tri-Loop

Бренды по названию

Популярные бренды