background image

    

ORION LC Installation and Operations Manual 

 

Multiplex Repeater Installation 2 x 3 

The 2 x 3 configuration allows you to connect two computers to the Orion 
LC and display the video of each to 3 DVI monitors.   
To configure Orion LC for a 2 input, 3 output Multiplex Repeater, set the dip 
switches and CATx or fiber cabling as shown below. Video received at the 
T1 input is transmitted out of the three R1 outputs, T2 input out the R2 
outputs. 
 

Set the dip switches so that switch 
1, 2, 4, and 5 are all in the “OFF” 
position, switch 3 in the “ON” 
position.

 

 

Each connectors labeled “T” (2) 
connects to a KVM CATx or fiber 
transmitter. 
 
Connectors labeled “R” (6) 
connect to KVM CATx or fiber 
receivers. 

(Local keyboard, monitor, and mouse not shown) 

 

Connect a DVI MM cable from the 
each CPU DVI graphic card to the 
DVI-In port on the transmitters 

Connect a single CATx or fiber 
cable from the transmitters to the 
Orion LC ports labeled “T1” and 
“T2”. 

Connect up to 3 CATx or fiber 
cables from the Orion LC ports 
labeled “R1” and 3 from “R2” to 
the receivers. 

Connect a DVI monitor to each 
receiver’s DVI output. 

Figure 2. Multiplex Repeater 2x3 

The video source can be from two computers as shown or from a single 
computer with a dual video card. The Transmitters can be two single video 
models as shown or one dual video model. 
 
 
 
 
 
 

  

 

             
                                  Receivers 
                              Orion LC 
 
Transmitters 

DVI Video Cable 
CATx or fiber Cable 

Содержание ORION lc













































Отзывы: