background image

Safe-T-Scope

®

  

Backup Camera System                                                                                  

                                                                 STSK7965

4                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      5

Camera mount in  
suggested location

 

Mount camera assembly high. (Centered)

 

Position of camera

Typical monitor image of view from
 properly installed camera

Obstructions behind truck

Position of camera

• Select a high and centered location at 
   the rear of the vehicle to mount the 
   STSC141 camera 
       

   IMPORTANT

• When mounting your  
   new backup camera, it is highly
   recommended that the image 
   transmitted by the camera show 
   the rear bumper and area behind
   the vehicle.  

• We do not recommend mounting  

 

   the camera near the lower area of  

 

   the vehicle (ex. bumper).  This reduces    
   the view of the camera and increases   
   the chance of physical damage to 
   the camera.  

  
• Once the location for the camera is 
   chosen, using a 3/16 drill bit, drill 
   four holes into the vehicle using 
   the bracket as a guid. Be sure to
   clear any obstacles before drilling holes. 

• Using a 5/8 drill bit, drill a hole into the 
   vehicle. Insert wire gramment and   
   safely pass the camera wire through   
   and mount securely in place. 

• To finalize the camera installation, hand 
   tighten the camera wire to your 
   extension cable. Make sure male 
   pins are inserted into female adaptor   
   correctly. You are ready to conceal 
   your extension cable. 

CAMERA INSTALLATION 

fig 1

fig 2

fig 3

Vehicle Rear Bumper 

• Connect the red wire to an ignition switched accessory (ex. radio) power source,
  and connect the black wire to chassis ground. See wiring diagram for connections.

• Attach monitor inside vehicle in a location convenient to the driver ( ex. center of dash,
  overhead, or flush-mounted in dash).

• Attach the "duckfoot" bracket to the dashboard or to the headline using self-tapping
screws and/or adhesive pad.

• Fasten monitor to "duckfoot" and adjust mounting angle to allow optimum driver viewing comfort.

• The monitor terminates in a 13-pin connector, which should be connected to the mating 13-pin
   receptacle end of the power/video/audio distribution harness.

• Connect the camera extension cable from the rear-view camera to the power/video/audio distribution 
   wire connector. The camera to cable connection is waterproof. Be sure to position the cable properly. 
   The male end attaches to the camera. The female end attaches to the power/video/ audio distribution 
   harness, typically located under the dashboard.

• The green wire is the REVERSE trigger wire. In typical rear-view installations, connecting this wire to the 
   vehicle's backup light circuit will activate the rear-view image whenever the vehicle shifts into reverse.

• Feed as much cable as possible into vehicle and clamp securely. This reduces the possibility of it 
   being hooked or snagged.

• Keep all cables away from

 

HOT, ROTATING and ELECTRICALLY NOISY components.

• FUEL TANKERS & OTHER SPECIALTY VEHICLES: All electrical equipment fitted to petroleum vehicles 
   must be connected via battery master switch and must be isolated from the battery while the vehicles 
   are loading and unloading. For other specialty vehicles, please check applicable code and regulations 
   prior to installation.

• Always consult your dealer when fitting any electrical or electronic equipment to a vehicle fitted with 
   a CAN-bus multiplex system. 

MONITOR INSTALLATION

Содержание SAFE -T-SCOPE STSK7965








Отзывы: